|
|
Company Name: |
Shenzhen Hong Ye Jie Technology Co., Ltd. |
Contact Person: |
Belle |
City: |
Shenzhen |
Country: |
China
|
Local Time: |
|
E-mail: |
Premium
Membership Required (Join Free Today) |
|
Introduction: |
RTV-2 molding silicone, addition silicone, pad printing silicone rubber, life casting silicone, electronic potting silicone rubber, FDA silicone, silicon oil, manual mold silicone, LSR, trademark silicone rubber, textile coating silicone rubber, liquid silicone rubber |
Business Type: |
Manufacturer |
Areas of
Interest: |
1. Chemicals/Rubber
|
|
|
|
Offers
From This Member (5) |
|
|
|
[Sell] Glass Fiber Rove |
|
|
Glass Fiber Rove Description of Glass Fiber Rove: Glass fiber rove for winding is suitable for reinforcing unsaturated polyester resin, vinyl resin, epoxy resin, polyurethane resin etc. Characteristics of Glass Fiber Rove: Uniform tension, speed and fully penetration, less hairiness, excellent mechanical properties. High hardness, low static, good dispersibility, good short cut ability. Application of Glass Fiber Rove: Aerospace, transportation, petroleum and natural gas pipeline, the roof of the vehicle, chemical equipment etc. Technical Parameters: Model Type Filament Diameter(μm) Linear Density(tex) Loss On Lgnition( Moiture Content Sizing Code Application WXS# E-Glass 8, 9 22, 33 0.01% 25% KH560 weave WCS# E-Glass 11-24 300,1200,2400,4800,9600 0.55±0.15% ≤0.1% 911 winding/pultrusion/ weave ZCS# C-Glass 11-24 300、1200、2400、4800、9600 0.55±0.20% ≤0.2% 911 winding/pultrusion/ weave GCS# A-Glass 11-24 300、1200、2400、4800、9600 6-7% / winding/pultrusion/ weave WDQCS# E-Glass 12-13 2400 0.50±0.15% ≤0.15% KH-512 winding/pultrusion/ weave SGS# E-Glass 11-13 2400-4800 0.55±0.15% ≤0.1% 911 winding/pultrusion/ weave Package: Each yarn group can be packed with heat shrink film or stretch film, and then placed in trays or boxes, each tray 48 or 64 yarn group, each yarn 15-18kg. According to the requirements of users can increase the weight of yarn group, but no more than 24kg.It can also be the packed into cartons, one roll each box. Container capacity: 1 x 20 foot container can hold 10 large and 10 small tray, net weight is about 20 tons For more information, please feel free to contact Ms. Belle: Tel: +86-0755-89212365 Fax: +86-755-89948030 Mob: +86-18938861895 Skype: hyw@resinpu.com E-mail: jpp@szrl.net QQ:2355542537 |
|
» Chemicals/Other |
|
|
|
[Sell] Glass Fiber Chopped Strand Mat |
|
|
Glass Fiber Chopped Strand Mat Glass Fiber Chopped Strand Mat Description: E-Glass Fiber chopped strand mat is a kind of non-woven glass fiber reinforced material, which is made by chopping glass fiber first, then be settled down non-directional and uniform, adding some powder or emulsion binder. It is mainly used for hand laying up process and laminating process, easy to process, with excellent forming performance. Chopped strand mat can be saturated with resin fast, with high transparency, at the same time, uniform fiber makes the products smooth on surface during the lamination process, good performance on coating model. Glass Fiber Chopped Strand Mat Characteristics: Weight is evenly distributed per gram Saturated fast Bubbles easy to be eliminated High transparency Excellent coating model performance Less consumption of resin. Glass Fiber Chopped Strand Mat Application: Mainly used for tank, winding pipe products, the surface layer of the glass products. Can improve the surface corrosion resistance and enhance the compressive strength for finished fiber glass products, prevent leakage, prolong the service life. Hand laying up type glass fiber mat is mainly used for hand laying up product with complex geometric curve, it is with excellent coating model performance, rapid resin saturated speed, can improve the strength and corrosion resistance performance for finished glass fiber mat products. Glass Fiber Chopped Strand Mat Technical Parameters: Model Type Mass per Unite Area(g/m2) Width(mm) Linear density(μm) Loss on lgnition(%) WDQ150 E-Glass 150 1040 11-13 1.5%-8.5% WDQ225 E-Glass 225 1040 11-13 1.5%-8.5% WDQ280 E-Glass 280 1040 11-13 1.5%-8.5% WDQ300 E-Glass 300 1040 11-13 1.5%-8.5% WDQ450 E-Glass 450 1040 11-13 1.5%-8.5% ZDQ280 C-Glass 280 1040 13-17 3.0%-6.0% FDQ300 CP-Glass 300 1040 13-17 3.0%-6.0% Glass Fiber Chopped Strand Mat Packaging: Packing Quantity Plastic Film+ Carton Box+Pallet About 10tons/ 20 ft 23tons/ 40ft For more information, please feel free to contact Ms. Belle: Tel: +86-0755-89212365 Fax: +86-0755-89948030 Mob: +86-18938861895 Skype: hyw@resinpu.com E-mail: jpp@szrl.net QQ:2355542537
|
|
» Chemicals/Other |
|
|
|
[Sell] high transparent making silicone rubber for castingcrystaline artificial |
|
|
high transparent making silicone rubber for castingcrystaline artificial Transparent silicone rubber Application: Transparent silicone rubber is specialize for crystal silicone mold, imitation zircon silicone mold , crystal resin diamond silicone mold, crystal facets diamond silicone mold, and polyester/ polyurethane/ epoxy section diamond silicone mold, rhinestone jewelry silicone mold, amber silicone mold, crystal jewelry silicone mold, imitation agate silicone molo, jade mold, jewelry rings silicone mold , boutique crafts molding and casting. Transparent silicone rubber Description: Transparent silicone rubber is the best choice for diamond molding, crystal molding, resin crystal rhinestone molding. Transparent silicone rubber is suitable for flat dies and special three-dimensional mold plastic mold replication Transparent silicone rubber is the best choice of mold making material for complex shape and high-precision products molding & casting. Transparent silicone rubber Characteristics: * Low shrinkage (less than 0.1% ) * High tensile and tear strength with high copy times * Hing heat resistance which can up to 250 °C * Easy for operation (mixing ratio at 1:1 /10:1) * Very good flow and easy for pouring operation * Fast and non-shrink cure at room temperature which can be accelerated considerably by the application of heat Transparent silicone rubber Technical Parameters: Model HY-MJ2135 HY-MJ2235 Appearance Transparent High transparent Mix ratio 10:1 10:1 Viscosity (cps) 70000 70000 Pot life(hrs) >2-3h >2-3 h Curing time(°C/min) 100-120°C/30mins 100-120°C/30mins Density/ g·cm-3 1.1 1.1 Hardness(A0) 35 35 Enlongation(%) ≥280 ≥320 Tear strength (KN·m-1) ≥15 ≥18 Tensile strength (Mpa) ≥4.8 ≥5.2 Shrinkage (%) 0.1 0.1 (Note: the above data for this product in 25°C temperature, 55percent humidity conditions, for reference. The accurate data is measured by customers when using.) More information about transparent silicone rubber, pls contact Ms.Belle: Tel: +86-0755-89212365 Fax: +86-0755-89948030 Mob: +86-18938861895 Skype: hyw@resinpu.com E-mail: jpp@szrl.net QQ:2355542537
|
|
» Chemicals/Other |
|
|
|
[Sell] Medical Grade liquid silicone rubber for shoe insoles |
|
|
Medical Grade liquid silicone rubber for shoe insoles pplication of Medical Grade liquid silicone rubber for shoe insoles: The product is a two component high elongation silicone gel designed for silicone food care products, such as silicone insole. This product cured at room temperature to a soft track gel with the addition of curing agent. The soft nature and cushioning effect offer this product provides excellent protection for our food health care. Technique Data of HY-Q625# Medical Grade liquid silicone rubber for shoe insoles: Model HY-Q625 Appearance Transparent Mixing Ratio 1:1 Operating time (Mins 25°C) 30-40 Curing time (Mins 25°C) 2-4h Hardness (A°) 25±2 Density ( g/cm 3 ) 1.08 Viscosity (CS) 6000 ± 2000 Tensile-strength( kgf/cm2 ) 3.3 Tear-strength (kgf /cm ) 8±2 Elongation-break(%) 420 Retractility(%) ≤0.1 Features of Medical Grade liquid silicone rubber for shoe insoles: 1.convenient 1:1 mixed ratio by weight 2.high elongation gel 3.low viscosity easily pourable 4.room temperature vulcanized and heat acceleration 5.soft track and selcky gel 6.absorbs shock and protets delicate mechanical component 7. no creativ by –product, no concerns nogarding corrosion Q: What are Foot Relief Insoles designed to do? A: Foot Relief Insoles are fluid filled insoles that have five primary benefits and a long list of secondary benefits. The insoles are designed to cushion, massage, absorb shock, give arch support, and increase circulation. The liquid insole will form to almost any shape foot giving you a customized fit after only a few minutes of wear. Many customers refer to our liquid filled insoles as "liquid orthotics" because of the way the insoles stretch slightly allowing the liquid to fill in the unique arches of your foot providing maximum comfort. Any questions abt Medical Grade liquid silicone rubber for shoe insoles , pls feel free to contact Ms.Belle: Tel: +86-0755-89212365 Fax: +86-0755-89948030 Mob: +86-18938861895 Skype: hyw@resinpu.com E-mail: jpp@szrl.net QQ:2355542537 |
|
» Chemicals/Other |
|
|
|
[Sell] Cement statue molding silicone rubber |
|
|
Platinum Cure Molding Rubber Silicone RTV Strengths for platinum cure molding rubber silicone RTV: Platinum cure molding rubber silicone RTV is used for prototyping and the reproduction of parts. Silicone moulds can be constructed in many different forms depending on the shape of the part you are making. In this section we will outline how to create the easiest one part flat back mould. Why platinum cure molding rubber silicone RTV: Silicone is the first choice of material when casting 3 dimentional shapes that contain undercuts as it exhibits excellent release properties, a high level of surface detail, very good chemical and high temperature resistance. It comes in a two-component system (base + catalyst) available in a hardness range of very soft to medium. It is available for making moulds that are poured, brushed or sprayed Features of platinum cure molding rubber silicone RTV: 1. Good characteristics of easy-operation 2. Light viscosity and good flowability 3. Low shrinkage 4. Favorable tension 5. No deformation 6. Favorable hardness 7. High temperature resistance, acid and alkali-resistance and ageing resistance 8. Food grade, non-toxic Datasheet of platinum cure molding rubber silicone RTV: Model Color Mixing ratio Pot life (mins) Demouled time (hrs) Hardness(A0) Tensile-strength (kgf/cm2) Tear-strength (kgf/cm) Viscosity (cps) Elongation (%) HY-E625 translucent 1 : 1 30-60 4±1 25±2 35±2 25±2 6000±3000 ≥400 HY-E630 translucent 1 : 1 30-60 4±1 30±2 40±2 23±2 7000±3000 ≥395 HY-E635 translucent 1 : 1 30-60 4±1 35±2 47±2 22±2 8000±3000 ≥470
Any questions for platinum cure molding rubber silicone RTV, pls feel free to contact Ms. Belle: Tel: +86-0755-89212365 Fax: +86-0755-89948030 Mob: +86-18938861895 Skype: hyw@resinpu.com E-mail: jpp@szrl.net QQ:2355542537
|
|
» Chemicals/Plastics |
|
|
|
|
|
Pages: 1
|
|
|
|