|
|
Offer
From Non Premium Member |
|
|
|
Type: |
Sell |
Subject: |
RTV Silicone rubber HY-638 for concrete casting |
Description: |
Usage: RTV Silicone rubber HY638 is most suitable for concrete castings, cement statue, concrete pavers, GRC cement products, etc. with the advantages of good tensile strength, high tear strength, high temperature resistance, high duplication times and repeated use, etc. It is suitable for large products with detailed pattern, which is difficult to demould. This silicone rubber is one of the products with the highest use level in the production of concrete castings and the shrinkage is up to 0.2%. Description:    RTV-2 molding silicon rubber and silicone rubber are general called two-component room temperature vulcanization silicone rubber with excellent fluidity and good operational performance. Add curing agent of 2%~5% at the room temperature, the silicone rubber is still operational within 30 minutes, and in 2-3 hours, an elastic silicon mold will be obtained with resistance to deformation, high-temperature, acid and alkali and expansion. Standard datasheet: Model appearance viscosity (cps): 20000~26000 Hardness (shore A): 32~36 Tensile Strength (Kgf/cm2):45~51 Tear strength (Kgf/㎝): 20~25 Elongation (%) ≧500 Mixing ratio (%):2~3 Operating time (h): 0.5 Curing time (h):2~4 Operation instruction for RTV-2 silicone rubber HY638#:   The product is white or red flowing liquid with general hardness of 22~50 shore A after curing. If the customer wants to make large products and large size molds, the mold should be made of silicone rubber with high hardness. On the contrary, if the mold with fine and precision patterns, it should be made of silicon with low hardness. The amount of the curing agent depends on the actual requirements of the customer. If molds requiring fast drying and demould, more curing agent is needed; contrarily, if molds requiring slower drying and demould, less curing agent is needed. Notes: We do not recommend adding silicone oil. If a special soft silicon mold or fine detailed and complex patterns products are required, 5%~10% silicone oil can be added to soften the mold for easy demould. The proportions and reactions of the curing agent and the silicon are listed as follows:    Adding curing agent 1%, the silicone can still be operated within 2.5 hours and can be demoulded after 6-8 hours.    Adding curing agent 2%, the silicone can still be operated within 50 minutes to 1 hour and can be demoulded after 2-3 hours.    Adding curing agent 3%, the silicone can still be operated within 28 - 30 minutes and can be demoulded after 1.5-2 hours. Adding curing agent 4%, the silicone can still be operated within 10 - 15 minutes and can be demoulded. Any further information pls feel free to contact with Ms Nina Shenzhen Hong Ye Jie Technology Co., Ltd.
|
Placement Date: |
Jun 21, 2012 |
Expiration Date: |
Jun 20, 2017 |
|
|
|
|
|
|
Company Name: |
Shenzhen Hong Ye Jie Tech Co., Ltd. |
Contact Person: |
Ms Nina |
City: |
Shenzhen |
Country: |
China
|
Local Time: |
|
E-mail: |
Premium
Membership Required (Join Free Today) |
|
Introduction: |
Hong Ye Jie Technology Co., Ltd. was established in 1998, it is a Science and technology corporation which is engaged in production, R & D, and sales of silicone rubber. We sets up Hong Kong Hongye Ltd., Shenzhen Hongye silicone rubber Factory and other affiliated enterprises in 2005. Our products including silicone products like silicone rubber, RTV-2 molding silicone rubber, manual design silicone rubber, shoe sole mold silicone rubber, silicon oil, pad printing silicone rubber, encapsulant and potting compound, silicone rubber for LED display, electronic thermolysis ointment, thermal conductivity silicone, special silicone rubber for CPU, silicone tube, silicone membrane, silicone sealant , liquid silicone rubber, addition cure RTV silicone rubber, HTV silicone rubber, solid silicone rubber, gross rubber, silicone rubber sheet, hot stamping silicone plates & roller, etc. These are currently been exported to Southeast Asia, Europe, the America and other 50 countries and regions. |
Business Type: |
Exporter, Manufacturer |
Areas of Interest: |
1. Chemicals/Rubber
|
|