|
|
|
Company Name: |
HONG YE JIE TECHNOLOGY CO.TLD |
| Contact Person: |
helenliao |
| City: |
Shenzhen |
| Country: |
China
 |
| Local Time: |
|
| E-mail: |
Premium
Membership Required (Join Free Today) |
|
| Introduction: |
Hong Ye Jie Technology Co.Ltd was established in 1998, is a Science and technology corporation which is engaged in R & D ,production, and sales of silicon rubber. We also established the Hong Kong Hongye LTD, Shenzhen Hongye Jie rubber Factory and other affiliated enterprises in 2005.
Our products includes 36 series in hundreds kinds of silicon products like Silicone rubber, silicone material, silicone product, RTV-2 silicone rubber, HTV-2 silicone rubber, mold making silicone rubber, pad printing silicone rubber, manual mold silicone rubber, condensation silicone rubber, casting silicone rubber, brushing silicone rubber, pouring silicone, room temperature silicone rubber，trademark silicone rubber, gross silicone rubber
|
| Business Type: |
Manufacturer |
| Areas of
Interest: |
1. Chemicals/Plastics
2. Chemicals/Rubber
|
|
|
|
Offers
From This Member (6) |
|
|
|
[Sell] silikon |
 |
|
silikon rubber description
silikon rubber are two part cold curing silicone rubbers. They consist of a base rubber and a curing agent and offer high performance for all moulding and casting applications. You are able to cast a wide variety of products from them ranging from plaster and cement through to polyester resins
silikon rubber 630#
Model
638#
Appearance
white
Mixing proportion of curing agent (%)
2%-3%
Operating time (hour 25 0C )
0.5
Curing time(hours 25 0C)
6-8
Hardness (A°)
30-32
Density ( g/cm 3 )
1.09
Viscosity (CPS 25 0C)
18000-25000
Tensile-strength(kgf /cm2 )
≥37
Tear-strength (kgf /cm )
≥26
Elongation-break(%)
≥ 500
Retractility(%)
≤0.3
The operating method of silikon rubber
1. Deal with the original mould.
2. spary release agent evenly on the original mould
3. weigh the silicone rubber and curing agent correctly and mix them evenly
4.Deairring and air bubble eliminating handling
5.perfusion or brushing process
silikon rubber Features:
A. a low cost way to make moulds
B. a mould is built using a layer process
C. more time and fairly lengthy process to make your mould
D. easy to use
E. amazing elongation to break
Interested in the items, please feel free to contact us.
www (dot) szrl (dot) net
http://wendyzhang2008(dot)diytrade(dot)com/
hyw(at)szrl(dot)net
Helenliao888(at)hotmail(dot)com
contact: Helen
Telephone:0086 755 89948019
Mobile: 0086-15889404068 |
|
| » Chemicals/Rubber |
|
|
|
[Sell] RTV silicone rubber |
|
|
RTV silicone rubber application:
RTV silicone rubber with Outstanding release properties, high mold life for casting of
primarily intended for poly resin crafts, PU crafts, PU resin crafts ,gypsum crafts ,unsaturated resin crafts, lighting and candles crafts ,plastic toy , stationery gifts crafts industry, , Europe component factory, simulation landscapes, animals and plants sculpture, sandstone crafts and so on.
Datasheet of RTV silicone rubber
Model: 625# mold making silicon rubber
Appearance: white
Viscosity (cs): 17000-20000
Hardness (A): 24-26
Tensile strength(kgf/cm2 ) ≥32
Tear strength (kgf /cm):≥28
Elongation break(%):≥500
Retractility (%):≤0.2
Curing agent mixed rate (%):2-3
Operate time (min): 30
Curing time (hours): 2-4
Model: 630# mold making silicon rubber
Appearance: white
Viscosity (cs): 25000-29000
Hardness (A): 28-32
Tensile strength(kgf/cm2 ) ≥35
Tear strength (kgf /cm):≥30
Elongation break(%):≥470
Retractility (%):≤0.2
Curing agent mixed rate (%):2-3
Operate time (min): 30
Curing time (hours): 2-4
Operating steps of RTV General Use silicone rubber for Plaster,resin, cements mold
1. Deal with the original mould.
2. spary release agent evenly on the original mould
3. weigh the silicone rubber and curing agent correctly and mix them evenly
4.Deairring and air bubble eliminating handling
5.perfusion or brushing process
Features of RTV silicone rubber:
(1) Free customer service to solve technical issues in earliest time.
(2) Curing agent arrange together as free charged
(3) Very low shrinkage and good dimensional stability
(4) High elasticity, for easy removal fo complex replica parts
(5) Sample orders are available.
(6) Special produce accordingly to your request
Storage and Precautions of RTV silicone rubber
RTV2 silicone rubber, which is an environmentally-friendly liquid silicone product, is not easy to burn and can be stored and transported
as non-hazardous goods. The shelf life of the product is about one year from
the date of production. Inspection is required when exceeding the time limited.
It can continue to be used in case of neither thickening nor deterioration.
www (dot) szrl (dot) net
http://wendyzhang2008(dot)diytrade(dot)com/
hyw(at)szrl(dot)net
Helenliao888(at)hotmail(dot)com
contact: Helen
Telephone:0086 755 89948019
Mobile: 0086-15889404068
|
|
| » Chemicals/Rubber |
|
|
|
[Sell] Manual Mold Silicon rubber |
|
|
Manual Mold Silicon rubber
Applications of Manual Mold Silicon rubber:
Manual mold silicone rubber is mainly applicable to manual mold design, PVC plastic molds, cement product molds, melting point alloy molds, alloy toy craftworks, plastic toy craftworks, gifts and stationery, large statues, duplication of cultural relics, shoe sole mold fabrication, pad printing positioning, shock resistance for electronic equipments, etc.
Features of Manual Mold Silicon rubber:
Manual mold silicone has good elasticity, non-deformation , high temperature resistance, low shrinkage. And it is suitable for manual mold design and small duplication mold production.
Description of Manual Mold Silicon rubber :
Manual mold silicon rubber is flowing liquid with consistant quality in whatever color. It consists of two components, wherein component A is silicone rubber, and component B is curing agent or vulcanizing agent. Firstly process and prepare the model mold or the product to be duplicated, take certain amount of the silicone rubber, add 2- 3% solidifying agent, and mix evenly for use. One mold pair can be solidified and formed in 2-3 hours. The formed mold can be used repeatedly without deformation and water shrinkage and with high temperature resistance, thereby providing fast duplication of the product with a product shrinkage 2‰.
Operation Instruction for Manual Mold Silicone rubber:
1. The manual mold silicon is applied to small products or products with fine patterns. The mold for the fine detailed and small products should be made of soft silicon to protect the products from easy breaking when demoulding.
2. If large product duplication or fabrication, the mold should be made of higher hardness silicone rubber so that the products made will not deform.
Payment Terms:L/C, T/T
Port: Shenzhen
Minimum order quantity:100kg
Supply ability:8 tons/day
Deliverly Time:within 3 days after getting bank receipt
Package:25kg/drum and 200kg/drum
If you need more information about RTV silicon rubber for manual mold making, please feel free to advise about your idea, then we will follow it to recommend the most suitable silicon rubber for your products. Looking forward to hearing from you
website: www (dot) szrl (dot) net
E-mail: hyw(at)szrl(dot)net
Helenliao888(at)hotmail(dot)com
Contact: Helen
Telephone:0086 755 89948019
0086 15889404068
|
|
| » Chemicals/Rubber |
|
|
|
[Sell] Pad Printing Silicone Rubber |
|
|
Pad Printing Silicone Rubber
Usage for Pad Printing silicone rubber:
Pad printing silicon rubber is mainly applicable to the printing of irregular patterns on plastics toys, electroplating products, electronic toys, trademarks, artwork gifts, and stationery, etc.
Features of Pad Printing silicone rubber:
The silicon pad is a carrier which transfer printing the patterns on the steel plate onto the toy products' surface. Pad Printing silicone rubber with the advantages of abrasion resistance, high temperature resistance, good printing effect, etc. , which made of top-quality raw material due to adding American Dupont Teflon high-temperature resistance new material, is processed through high-temperature machining.
Instruction for Pad Printing silicone rubber
1． Firstly,clean the mold with detergent, and dry up the mold by a piece of cloth or an air gun and then coat the mold with a layer of release agent.
2. The normal proportion between the pad printing silicon and the silicone oil depends on the requirements of the customers. If pattern with big area to be printed, a soft silicon pad is needed and the amount of silicone oil is increased. Contrarily, if a silicon pad with high hardness is needed, the silicone oil should be added less or not . The hardness of general pad printing silicone rubber is approximate of 15A°~-25 A°.
3. General mixing proportion is as follows: add 30g silicone oil into 100g silicon with the hardness of the silicon pad being 20A°, which is suitable for the pad printing for alloy car and products with small patterns and contact areas. If a big pressure contact surface or a soft silicon pad is needed, the mixing proportion between the silicon and the silicone oil can be 100:30-100:50.
4. The amount of the curing agent and the chemical reaction with the silicon is as follows: mix 100g silicon and 50g silicone oil sufficiently and evenly, then add the curing agent which is 2%-3% of the total weight of the silicon and the silicone oil, mixing for 2-3 minutes, and then deair to remove the air bubbles . The time of deairring generally does not exceed 10 minutes. If the deairing time is too long,it may cause fast curing of the silicon and impact the quality of silicon.
Payment Terms:L/C, T/T
Port: Shenzhen
Minimum order quantity:200kg
Supply ability:8 tons/day
Deliverly Time:within 3 days after getting bank receipt
Package:25kg/drum and 200kg/drum
If you need more information about RTV silicon rubber for manual mold making, please feel free to advise about your idea, then we will follow it to recommend the most suitable silicon rubber for your products. Looking forward to hearing from you
website: www (dot) szrl (dot) net
E-mail: hyw(at)szrl(dot)net
Helenliao888(at)hotmail(dot)com
contact: Helen
Telephone:0086 755 89948019
0086 15889404068
|
|
| » Chemicals/Rubber |
|
|
|
[Sell] Silicon rubber for mould making |
|
|
Silicon rubber for mould making
Applications of mould making silicon rubber
Silicon rubber for mould making is mainly used for poly resin crafts, gypsum crafts, unsaturated resin crafts, lighting and candle crafts, plastic toys, stationary gifts crafts industry, a large statue Buddha, large-scale cement mold, aninamls and plants sculpture, relievo furniture, cultural relic product, etc.
Features of molding silicon rubber:
Silicon rubber for mold making with general hardness of 22-55 A0 after curing. Molding silicon rubber is a kind of flowing liquid which features with good resistance to deformation, good tensile and tear strength, acid-alkali as well as high reproduction times, good flowability and easy operation.
Instruction for molding silicon rubber
If customer wants to make large products and large size molds, the mold should be made of silicon rubber with high hardness. On the contrary, if the mold with dedicate and precision patterns, it should make of silicon rubber with low hardness. The mixing ratio between the silicon rubber and the curing agent depents on the customers’ requirement. If clients needs fast drying and demold, more curing agent will be added; contrarily, if molds requiring slower drying and demould, less curing agent is needed.
(Note: our company does not recommend you to add silicon oil, if a special soft silicon mold or fine or dedicate pattern products are required, 5%-10% silicon oil can be added to soften the mold for easy demould)
Frequently asked questions of mold making silicon rubber
1. Why should the silicone mold be reused only for a few times?
It can be due to the following reasons:
a. Adding too much silicone oil in to silicon rubber. Silicon oil is an additive which destroies the molecular weight of silicone rubber and reduce the tension and tear strength.
b. Using the silicon rubber with a high hardness to make molds for small sized products with delicate and intricate designs and the silicon rubber with a low hardness to makes molds for large sized products with simple designs.
(Notes: we should choose the silicon rubber specifically according to the requirements of our products to avoid this problem.)
2. Why is the appearance of the finished mold striate and unsmooth?
It is because the appearance of the product or the model itself is not perfect, and it has not been polished before the further operation. So when you make silicon molds, firstly you should polish the product, spray the mold spray evenly on the product. In this case, the problem can be avoided.
Payment Terms:L/C, T/T
Port: Shenzhen
Minimum order quantity:200kg
Supply ability:8 tons/day
Deliverly Time:within 3 days after getting your payment
Package:25kg/drum and 200kg/drum
If you need more information about RTV silicon rubber for mold making, please feel free to advise about your idea, then we will follow it to recommend the most suitable silicon rubber for your products. Looking forward to hearing from you
website: www (dot) szrl (dot) net
E-mail: hyw(at)szrl(dot)net
Helenliao888(at)hotmail(dot)com
Contact: Helen
Telephone:0086 755 89948019
0086 15889404068
|
|
| » Chemicals/Rubber |
|
|
|
[Sell] RTV 625# equivalent to 3481# |
|
|
Application of RTV 625#
RTV 625# for molding making are used for mold duplication and delicate mold making for poli crafts,resin crafts lighting and candle crafts, plaster, cements and so on.
The operating method of RTV 625# mould making
1. Deal with the original mould.
2. spary release agent evenly on the original mould
3. weigh the silicone rubber and curing agent correctly and mix them evenly
4.Deairring and air bubble eliminating handling
5.perfusion or brushing process
RTV 625# datasheet
Item 625
viscosity(CS) 15000-18000
Hardness shore A 25
Tensile-tstrength (kgf/cm2) 35
Tear-strength(kgf/cm) 26
elongation: (%) 400-420%
shrinkage: (% 0.3%
Features of RTV 625# silicon:
(1) Silicon rubber for pad printing with SGS and ROSH approval
(2) Curing agent arrange together as free charged
(3) In liquid form and in various colors
(4) With an exceptional fluidity and good operability.
(5)Temperature and deformation resistance as well as low shrinkage.
(6) High duplication times.
(7) Sample orders are available
(8) MOQ: 200KG
Frequently asked questions about RTV mould making silicon
Why does the mold making silicone rubber mold have few molding times?
1.adding too much silicone oil which will destroy the molecular of silicone rubber;
2.Making the mold for small and detailed patterns products with higher hardness silicone rubber which is easy to break;
Making the mold for large and simple products with soft silicone rubber which will reduce the tensile and tear strength of the mold, and the mold will have deformation.
Thus, we should take the proper silicone rubber to make the mold for suitable products.
If you have meet any problem with the mould now, please feel free to contact us, hope we can do something fo you and your company, or you want to learn how to make silicon mould, we will offer professional technology information for your reference
www (dot) szrl (dot) net
http://wendyzhang2008(dot)diytrade(dot)com/
hyw(at)szrl(dot)net
Helenliao888(at)hotmail(dot)com
contact: Helen
Telephone:0086 755 89948019
Mobile: 0086-15889404068 |
|
| » Chemicals/Rubber |
|
|
|
|
|
Pages: 1
|
|
|
|
|
