|
|
|
Company Name: |
zhongguo hongyejie co.ltd |
| Contact Person: |
jasminechan |
| City: |
shenzhen |
| Country: |
China
 |
| Local Time: |
|
| E-mail: |
Premium
Membership Required (Join Free Today) |
|
| Introduction: |
Hong Ye Jie Technology Co., Ltd. established in 1998, is a Science and technology corporation which is engaged in production, R & D, and sales of silicone rubber. It sets up Hong Kong Hongye Ltd., Shenzhen Hongye silicone rubber Factory and other affiliated enterprises in 2005. |
| Business Type: |
Manufacturer |
| Areas of
Interest: |
1. Chemicals/Rubber
|
|
|
|
Offers
From This Member (10) |
|
|
|
[Sell] BMZ020#Non-Alkali Glass fiber surface mat |
 |
|
Description
Glass fiber surface mat is mainly used in the surface layer of glass products. Divided into two categories: specific wound type series (S-SM)and hand lay-type series (S-HM)
Characteristic
Fiber distribution evenly, finished products with smooth surface, corrosion resistance, low binder content, volt mode is good
Application
Wound glass fiber mat is mainly applied to the surface of the pipe and tank wrap products, it can improve product surface corrosion resistance and enhanced compressive strength, anti-leakage and prolong life.
Hand lay glass surface mat is mainly used for hand lay products with complex geometric curve, its volt mode is good, resin penetration speed, can improve the strength and corrosion products.
Datasheet
Product name Alkaline or not gram weight
(g/m2) breadth（mm)
BMZ020# Not Alkali 20 20-2000
Shelf life
12-24 months under the room temperature of 25C
Contact: Jasmine Email: hyjcchuan(at)szrl(dot)net Skype: Jasminechanszrl
Tel:0086-18938867607
|
|
| » Chemicals/Other |
|
|
|
[Sell] WFB200# Glass Fiber Cloth |
|
|
Description
Glass Fiber cloth is compiled by untwisted direct roving with plain weave, is mainly for unsaturated polyester resins , vinyl resins , epoxy and phenolic resins , etc.
Application
Widely used for hand laying fiberglass products : such as the hull , automobile, airplane , plates, sports and entertainment facilities , fiberglass products, sanitary ware, pipe irrigation , cooling towers and so on.
Technical Parameters
Model Code WFB200
Concluding alkali or not No
Weight(g/m2) 200
Width(mm) 500-3300
Characteristics
＊Less Hairy
＊High penetration speed
＊Uniform thickness
＊High mechanical strength
Warm tips :
1,General conventional glass fiber filaments is 9-13 microns in diameter , glass fiber below 6 micron belongs to floats , can be sucked directly into the lungs, can cause respiratory disease, so you should pay special attention to six microns or less glass fiber cloth, is generally imported. The one who is under professional production operations must wear masks. If contact frequently, may be bothered into the lungs, causing pneumoconiosis .
2, if it is physically touch the glass fiber, people with allergic skin will occur allergic itching, however, generally speaking, it is not serious. It will occur small rash on allergic skin, please take some anti allergy medicine
3, if it is stick on clothes and difficult to remove, just pat it under wind for several times or clean & dry it
Package
Each volume sets wrap a transparent plastic bag , then put into cartons. If you have special packaging requirements , we can offer in accordance with customer requirements. 1x20 foot container can pack about 10 tons
Contact: Jasmine Email: hyjcchuan(at)szrl(dot)net Skype: Jasminechanszrl
Tel:0086-18938867607
|
|
| » Chemicals/Other |
|
|
|
[Sell] HY103# Unsaturated Resin |
|
|
Description
HY103# with high hardness, not easy to be broken, suitable for the production of many crystal crafts production
Application
Suitable for production of crystal lamp, candle holder, crystal crafts, crystal gifts, crystal trophy,crystal vase, crystal model building mode, crystal perfume bottles, crystal ashtray, crystal vase, hotel supplies, crystal stationery cards Taiwan, crystal ball, crystal key button, crystal animal, flower and so on transparent products.
Technical Parameters
Mix Ratio
Color
Appearance High Transparent liquid material
Acid Number( AN) 15-21
Viscosity 350-600
（%）ration of Solid 65-70
Gel time 9-15
water absorption ( 24H) 0.05%
Characteristics
＊Not easy to be broken
＊High Hardness
Operation Ways
1, First, take a mount of resin, then add 0.5% - 1% cobalt ( Thixtropic ) ,and stirring evenly;
2, Then add 0.8%-1.5% catalyst according to the amount of the resin and stirring evenly;
3, For the cure time is closely to the environmental temperature and humidity , so pls adjust the mix ratio of the catalyst and thixotropic
4The gel time of about 9-15 minutes at room temperature of 25C.
Warm tips :
1., It is belong to flammable items, pls avoid fire, and child contact, If contact with skin , pls wash by clean water and go to a doctor.
2, Don’t add the Thixotropic and cure agent at the same time , Otherwise , it will be eexplosion and fired, 3. The catalyst and the Thixotropic must be isolated storage
Package
Resin : 220KG/Iron drum package
Thixotropic : 25kgs per Plastic Drum
Cure Agent : 25kgs per Plastic Drum
Shelf life
Under the temperature of 25℃ storage for a period of three to six months
Contact: Jasmine Email: hyjcchuan(at)szrl(dot)net Skype: Jasminechanszrl
Tel:0086-18938867607
|
|
| » Chemicals/Other |
|
|
|
[Sell] JA205# Foam PU Resin |
|
|
Description
JA205# foaming resin is a new organic polymer material, Commonly known as the black material and white material, also known as PU material, foam material, combination of materials, black oil and butter. An independent closed-cell structure of the polyurethane rigid foam will be appeared by mix the part A and Part B evenly at ratio of 1: 1 . because of its superior performance ,It is widely used in many fields .
Application
Mainly used for the Insulation material for : refrigerators, freezers, solar energy, high temperature chamber and other electrical companies, cold storage, refrigerated trucks industry, construction, pipe insulation industry, telecommunications, shipbuilding, wood furniture, handicrafts, packaging and other fields. Products are also applications involving light industry, chemical industry, electronics, textiles, medical, construction, building materials, automotive, defense, aerospace, aviation, etc., such as: fishing rod handles, drinking fountains coolers, automotive portable electronic refrigerator, mug, electricity water heaters, general equipment insulation sheet, and so on.
Technical Parameters
Code Mix Ratio Color Flash Point Viscosity（25℃cps ） Froth time Demould Time（60℃）
JA205# A:B=1:1 A：Black ≥200 170～3000 1-2min 5-6min
B：White 150-300
Characteristics
＊An Low density, high strength,
＊good thermal insulation properties,
＊good thermal insulation properties,
＊non-absorbent,
＊quick and easy construction and other excellent characteristics,
＊acid and alkali resistance, aging resistance,
＊excellent production and processing performance characteristics.
＊heat insulation, sound insulation
＊capacity of light, high-strength, , fire-retardant
Operation instructions
1 Clean the mold surface and coated with a layer of release agent,
2 Mix the part A and Part B at ratio 1: 1 (black material: white material = 1: 1 ) For hard spots, add more black material) Then mixing evenly, poured into the mold.
3.1-2 minutes to start foaming reaction can be stripping out 5-6 minutes (60 ℃) after.
Warm tips :
1 It is forbidden to pour back the material into the Original packages even it is unused ;
2 construction to be dry and well ventilated space, Far away from the fire source;
3 stored in a cool dry place,Far away from light , and close the packages well .
4 Don’t contact with skin or eyes , Otherwise clean the skin with alcohol scrub, and wash with plenty of water and go to hospital in necessary
Package
25KG/drum package for part A + 25KG/drum packages for part B
200KG/drum packing for part A +200KG/drum packing for part B
Shelf life
Six (6) months when stored under dry and cool place by original package under 25℃
Contact: Jasmine Email: hyjcchuan(at)szrl(dot)net Skype: Jasminechanszrl
Tel:0086-18938867607
|
|
| » Chemicals/Other |
|
|
|
[Sell] HY302#Epoxy Resin |
|
|
Description
HY302# epoxy resin is composed of two components, resin and curing agent, with mix ratio of 4: 1 ( Resin : Cure Agent = 4: 1 ) , suitable for and amine curing agents or their additive , It can be cured at room temperature and heated Cured.
Application
Widely used in Painting such as for floor, coating ect , It can also used for electronic potting , such as
power transformer, reactor, CCL, insulating paint, electrical appliances and laminated products and other fields.
Technical Parameters
Mix Ratio 4: 1
Color A: 、B:
Appearance
no visible mechanical impurity / liquid Form
(eq/100g)Epoxide Value 0.48—0.54
(eq/100g)Unhydrolytic Chlorine ≤300
weight per epoxy equivalent (WPE)(g/eq) 185-210
Viscostiy（mPa.S） 10000-11000
(%) Volatile ≤1.8
Colour ≤3
(℃) Softening Point
Characteristics
＊Strong adhesion
＊Good chemical corrosion resistance
＊Thermal stability and electrical insulation.
＊ high toughness
＊Low Shrinkage
Operation instructions
1. Clean the surface of your products , make it clean and dry
2: evenly mixing the seasoning ratio A:B=4:1
3 Introduction resin mixing evenly to the electronic equipment inside, so that it can be estimated
Warm tips :
1 It is forbidden to pour back the material into the Original packages even it is unused ;
2 construction to be dry and well ventilated space, Far away from the fire source;
3 stored in a cool dry place,Far away from light , and close the packages well .
4 Don’t contact with skin or eyes , Otherwise clean the skin with alcohol scrub, and wash with plenty of water and go to hospital in necessary
Package
20KG/drum package
220KG/drum package
Shelf life
Six (6) months when stored under dry and cool place by original package under 25℃
Contact: Jasmine Email: hyjcchuan(at)szrl(dot)net Skype: Jasminechanszrl
Tel:0086-18938867607
|
|
| » Chemicals/Other |
|
|
|
[Sell] Liquid Pad Printing Silicone Rubber Material |
|
|
1. Applications of liquid pad printing silicone rubber
Pad printing silicone rubber is mainly use for printing irregular patterns of plastic toys, electroplating toys and trade makers . Pad printing silicone rubber as a carrier which transfer patterns on the steel plate to the toys products surface.
2. Features of liquid pad printing silicone rubber
a. resistance to deformation, high-temperature
b. high printing times
c. good aging resistance
d. exceptional elasticity
e. great printing effect
3. Operation Instructions of liquid pad printing silicone rubber
Pad printing silicone rubber is two-component silicone, part A is liquid silicon rubber, part B is catalyst. The usual mixture of silicone rubber and catalyst is 100: 2 or 100: 3. E.g. we take 100g of liquid silicon rubber and 2g-3g catalyst, mix them and pour it to your mold. A fter 2-4 hours, you will get a Pad printing silicone rubber.
. FAQ of liquid pad printing silicone rubber
Why the silicon pad is non-durable？
This problem is caused not by the liquid silicon rubber itself, but in the process of filtering, the filtering handled not properly and impurities are not all filtered out; or in the process of packing as containers not cleaned thoroughly.
As the silicon oil will break the molecular chain of the silicon rubber. More silicon oil added, softer the pad printing will be, meanwhile nondurable and easy ageing it will also turn to be.
Some customers do not know well about the performance of silicon rubber. Actually, the durability of printing pad is closely related to the size of printing pattern. Some factories do not want to take the trouble to change the printing pad. While in fact, for large pattern, large silicone pads should be used, otherwise, use small one.(Generally, the ratio of the silicone pad to printing pattern is 3:1)
Contact: jasminechan
skype:jasminechanszrl
Tel: +86-755-89212365
Fax:+86-755-89948030
Mobile：18938867607
E-mail： hyjcchuan@szrl.net
youtube: jasminechanszrl@gmail.com |
|
| » Chemicals/Rubber |
|
|
|
[Sell] Medical Grade liquid silicone rubber for shoe insoles |
|
|
Application of Medical Grade liquid silicone rubber for shoe insoles
The product is a two component high elongation silicone gel designed for silicone food care products, such as silicone insole.
This product cured at room temperature to a soft track gel with the addition of curing agent. The soft nature and cushioning effect offer this product provides excellent protection for our food health care.
Technique Data of HY-E625# Medical Grade liquid silicone rubber for shoe insoles
Model HY-E625#
Appearance Translucent
Mixing Ratio 1:1
Operating time (Mins 25°C) 30-40
Curing time (Mins 25°C) 2-4h
Hardness (A°) 25±2
Density ( g/cm 3 ) 1.08
Viscosity (CS) 6000 ± 2000
Tensile-strength( kgf/cm2 ) 60 ± 2
Tear-strength (kgf /cm ) 15±2
Elongation-break(%) 470
Retractility(%) ≤0.1
Features of Medical Grade liquid silicone rubber for shoe insoles
1.convenient 1:1 mixed ratio by weight
2. high elongation gel
3. low viscosity easily pourable
4.room temperature vulcanized and heat acceleration
5. soft track and selcky gel
6. absorbs shock and protets delicate mechanical component
7. no creativ by –product, no concerns nogarding corrosion
Q: What are Foot Relief Insoles designed to do?
A: Foot Relief Insoles are fluid filled insoles that have five primary benefits and a long list of secondary benefits. The insoles are designed to cushion, massage, absorb shock, give arch support, and increase circulation. The liquid insole will form to almost any shape foot giving you a customized fit after only a few minutes of wear. Many customers refer to our liquid filled insoles as "liquid orthotics" because of the way the insoles stretch slightly allowing the liquid to fill in the unique arches of your foot providing maximum comfort.
Contact: jasminechan
skype:jasminechanszrl
Tel: +86-755-89212365
Fax:+86-755-89948030
Mobile：18938867607
E-mail： hyjcchuan@szrl.net
youtube: jasminechanszrl@gmail.com |
|
| » Chemicals/Rubber |
|
|
|
[Sell] life casting silicone rubber for male sex organ sexual penis |
|
|
Description of life casting silicone rubber for male sex organ sexual penis
It is generally named two-components silicone rubber which will be cured under room temperature, Part A is a flowable liquid, part B is the curing agent.
It features an exceptional fluidity and good operability.
The mixing ratio is 1:1,mainly be suitable for making FDA & Medical products.
It could be used to make sexy toys, human penis, female vagina vibrator.
Technical Parameters silicone rubber for the imitation of male sexual organs penis
Model HY-E620#
Appearance Translucent
Mixing Ratio 1:1
Operating time (Mins 25°C) 20-30
Curing time (Mins 25°C) 60-90
Curing time (Mins 60°C) 10-15
Hardness (A°) 20±2
Density ( g/cm 3 ) 1.08
Viscosity (CS) (Part A) 6000-8000
Viscosity (CS) (Part B) 6000-8000
Viscosity (CS) (After mixed) 6000 ± 1000
Tensile-strength( kgf /cm2 ) 75 ± 20
Tear-strength (kgf /cm2 ) 24 ± 2
Elongation-break(%) 420 ± 50
Retractility(%) ≤0.1
Contact: jasminechan
skype:jasminechanszrl
Tel: +86-755-89212365
Fax:+86-755-89948030
Mobile：18938867607
E-mail： hyjcchuan@szrl.net
youtube: jasminechanszrl@gmail.com |
|
| » Chemicals/Rubber |
|
|
|
[Sell] Liquid platinum cure silicone rubber for adult women sex toys making |
|
|
1. Description -Liquid platinum cure silicone rubber for adult women sex toys making
Liquid platinum cure silicone rubber for adult women sex toys making is generally named two-components silicone rubber, Part A and part B. It features an exceptional fluidity and good operability.
The mixing ratio is 1:1 or 1:1,mainly be suitable for making molds for adult sex toys, it’s FOOD GRADE silicone rubber.
2. Other Applications - Liquid platinum cure silicone rubber for adult women sex toys making
This liquid silicone rubber not only excellent for adult women sex toys making, it could also be mainly used for making concrete stones, wax molds, PU molds, resin molds, gypsum casting, candle molding and
chocolate , candy and any other FDA food product mold making,prototyping etc.
3. Instruction- Liquid platinum cure silicone rubber for adult women sex toys making
Liquid platinum cure silicone rubber for adult women sex toys making are generally named as two-part room temperature sulfurated silicone rubber, which features an exceptional fluidity and good operability. When mixed with 2-3% curing agent, they can still be operated within 30 minutes, but will be formed after 2-3 hours. With resistance to deformation, high temperature, acid and alkali, and expansion, silicon flexible molds are used for mold duplication and delicate mold making for poli crafts, resin crafts lighting and candle crafts.
4. Features- Liquid platinum cure silicone rubber for adult women sex toys making
(1)high tensile & tear strength
(2) Low linear shrinkage
(3)free Curing agent
(4)brushing & pouring
(5) high duplication times
Contact: jasminechan
skype:jasminechanszrl
Tel: +86-755-89212365
Fax:+86-755-89948030
Mobile：18938867607
E-mail： hyjcchuan@szrl.net
youtube: jasminechanszrl@gmail.com |
|
| » Chemicals/Rubber |
|
|
|
[Sell] Platinum Cure Molding Rubber Silicone RTV |
|
|
Strenghts for platinum cure molding rubber silicone rtv
Platinum cure molding rubber silicone rtv is used for prototyping and the reproduction of parts. Silicone moulds can be constructed in many different forms depending on the shape of the part you are making. In this section we will outline how to create the easiest one part flat back mould.
Why platinum cure molding rubber silicone rtv
Silicone is the first choice of material when casting 3 dimentional shapes that contain undercuts as it exhibits excellent release properties, a high level of surface detail, very good chemical and high temperature resistance.
It comes in a two-component system (base + catalyst) available in a hardness range of very soft to medium. It is available for making moulds that are poured, brushed or sprayed
Features of platinum cure molding rubber silicone rtv
1. Good characteristics of easy-operation
2. Light viscosity and good flowability
3. Low shrinkage
4. Favorable tension
5. No deformation
6. Favorable hardness
7. High temperature resistance, acid and alkali-resistance and ageing resistance
8. Food grade, non-toxic
Datasheet of platinum cure molding rubber silicone rtv
Model Color Mixing ratio Pot life (mins) Demouled time (hrs) Hardness(A0) Tensile-strength (kgf/cm2) Tear-strength (kgf/cm) Viscosity (cps) Elongation (%)
RTV E625 translucent 1 : 1 30-60 4±1 25±2 35±2 25±2 6000±3000 ≥400
RTV E630 translucent 1 : 1 30-60 4±1 30±2 40±2 23±2 7000±3000 ≥395
RTV E635 translucent 1 : 1 30-60 4±1 35±2 47±2 22±2 8000±3000 ≥470
Operation of platinum cure molding rubber silicone rtv
RTV625 is suitable for making moulds for small size products by pouring method;
RTV630 is suitable for making moulds for small or medium size products by pouring and brushing method;
RTV638 is suitable for making moulds for large size products by brushing method.
|
|
| » Chemicals/Rubber |
|
|
|
|
|
Pages: 1
|
|
|
|
|
