- marketplace of exporters and importers Contact with us Trade offers catalog Trade companies catalog Join free today Help
Global Importers and Exporters Network  

Popular searches: phone fabric food phone card yarn fish permanent comedo comedo extractors fish meal

Home » Offers Catalog » Chemicals » Rubber » HY 9055 Electronic Potting Compound silicon rubber
Member's Login
» Join Free Today
» Forgot Password
New Offers
[Sell] motor for microwave oven
[Sell] fuse with holder for microwave oven
[Sell] transformer for microwave oven
[Sell] Al drawer handle for refrigerator
[Sell] LG Magnetron 2M213
» Post New Offer
New Companies
China Qingdao Frankeh Trading Co., Ltd
Slovak Republic copper land llc
[Slovak Republic]
India bajajfinanceltd646
China Qingdao teland chemical co.,ltd
Qatar mohamed consulting agency
» Join Free Today
Visit Our Partners is the best source of news and events in Africa. - Marketplace for buyers and sellers

Business Directory

Necklace Making

Offer From Non Premium Member

Type: Sell

HY 9055 Electronic Potting Compound silicon rubber

Description: Product Feature
HY 9055 is a kind of low viscosity, Inherent flame resistance, two components addtion cured potting silicone with heat-conducting. It cures with both on room temperature and heated temperature. It has the feature of the higher temperature the faster of the curing time. It can be applied to electronic components for insulation, waterproofing, fixed and flame retardant. It mainly applied in electronic components surface with materials of PC(Poly-carbonate)、PP、ABS、PVC, etc. and metal materials.
Typical Application
HY 9055 could be applied to
- high powered electronics,
- DC/DC module and circuit board which requires heat dissipation and high temperature resistance.
-It can be broadly used for LED screen, Wind Power Generator, PCB substrate, etc.
Technical Parameters
Features Part A Part B
Before Curing Appearence Gray Fluid White Fluid
Viscosisty(25℃cps) 2500±500 2500±500
Operation features Mixing Ratio 1:1
Viscosisty(after mixing) (cps) 2000~3000
Operating Time(25℃ hr) 120
Curing time (min,25℃) 480
Curing time(80℃ hr) 20

After Curing Hardness(Shore A) 55±5
Thermal conductivity [W(m•K)] ≥0.8
Dielectric Strength(KV/mm) ≥25
Volume Resisivity(Ω•cm) ≥1.0×1016
linear expansibility [m/(m•K)] ≤2.2×10-4
Fire Resistance 94-V1
(Pls note: the above data for this product in 25 ℃ temperature, 55 percent humidity conditions, for reference. The accurate data is measured by customers when using.)
1, Pls put part A and part B in separate container and stir evenly before mixing the two part together.
2, Mixing Ratio: part A: part B = 1:1
3, Deaeration the mixture in vacuum pump under 0.08 MPa for 3-5 minutes.Then the mixture could be used for pouring.
4, Pls note that the thickness of the silicone affects the curing time. If the silicone used is a little thick,then the curing time will be a little longer.The temperature also affects the curing time.When in lower temperature, we suggest customers appropriately heat the mixture to accelerate vulcanization. With temperature of 80~100℃, the silicone will cure in 15 minutes; while in 25℃ room temperature, the silicone will cure around 8 hours.
1.The following material may hinder the curing of HY 9055, So pls use after the test. When necessary, pls clean the application areas.
 Organotin compound or Condensation silicone with organotin
 Sulphur, sulfide and sulfur rubber materials.
 Amine compounds as well as contains the amine materials.
 Pewters solder flux
2. HY 9055 should be sealed storage.The mixture should be used up disposably to avoid causing waste.
3. HY 9055 belongs to non-dangerous goods, but keep away from mouth and eyes.
4. When it gets stratified after a period of storage, Please mix it evenly before using,which does not affect the performance.

20Kg/pail as a set (Part A 10Kg + Part B 10Kg)
Any comments pls feel free to contact Ms Sabrina
Tel: +86-755-89948006
Mob: +86-18938867533
Skype: sabrinapeng0601
Placement Date: Aug 10, 2015
Expiration Date: Aug 08, 2020

Company Information

Company Name: Hongkong Hong Ye Silicone Technology Co.,Ltd
Contact Person: Ms.sabrina
City: shenzhen
Country: China China
Local Time:
E-mail: Premium Membership Required (Join Free Today)
Introduction: We are a joint venture specializing in the manufacturing of molding silicon rubber, mold duplicating rubber for resin craft makers ,special silicon for manual molding ,shoe mold rubber ,pad printing silicon ,silicon oil ,107 base ,DMC etc for plastic toys factories ,With a product line of tens of categories ,we can offer quick copying with precise contraction ratio(up to two thousandth) for mold making .to reach the internationally leading quality standard with competitive price is our best ambition that merits your trust.
It is our solemn commitment that :any of our products with quality problems will be replaced within 3 months after purchase ;we offer on –site follow –up service for product demonstration ,free customer service to solve technical training on pad printing silicon usage and rubber head making .What you need is also what we pursue .We are committed to back you up in producing first class products .Customers old and new and distribution and deputization .Let’s join hands and strive for mutual prosperity
Business Type: Exporter, Manufacturer
Areas of Interest: 1. Building & Construction/Architecture
2. Building & Construction/Construction
3. Chemicals/Organics

» Join Free Today


Home | Advertise With Us | Contact Us | Privacy | Terms Of Use | Links
© 2001-2019, Inc. All Rights Reserved
Visit our partners: Marketplace for buyers and sellers  | International trade offers and trade leads directory  | Online trade database of manufacturers, exporters, importers and suppliers  | International trade directory of exporters, importers, manufacturers and suppliers