|
|
|
Offer
From Non Premium Member |
|
|
|
Type: |
Sell |
| Subject: |
E625Addition Molding Silicone rubber |
| Description: |
HY- E625Addition Molding Silicone rubber
Description:
HY-E625# addition molding silicone is generally named two-components silicone rubber, Part A is a flowable liquid, part B is the curing agent. It features an exceptional fluidity and good operability. The mixing ratio is 1:1, mainly be suitable for making molds application.
Applications:
HY- E625# addition molding silicone could be mainly used for making concrete stones, precision molds, PU molds, for life casting, fabric finishing, shoe soles making， seal for electronic components and solar circuit board, trademark decoration. etc.
Technique Data:
Model HY-E625#
Appearance Translucent
Mixing Ratio 1:1
Operating time (Mins 25°C) 30 - 50
Curing time (Mins 25°C) 120 - 240
Curing time (Mins 60°C) 20 - 30
Hardness (A°) 25±2
Density ( g/cm 3 ) 1.08
Viscosity (CS) (Part A) 30000 ± 5000
Viscosity (CS) (Part B) 5000 ± 500
Viscosity (CS) (After mixed) 10000 ± 2000
Tensile-strength( kgf /cm2 ) 50± 5
Tear-strength (kgf /cm2 ) 15 ± 2
Elongation-break(%) 500 ± 50
Retractility(%) ≤0.1
OPERRATING INSTRUCTION:
1. Clean your products and brush a layer of release agent (detergent or soap water) on the surface of your product.
Note: The model should not have been used to make molds for tin cured silicone rubber before. Otherwise, the addition silicone will not get cured. (Use a new model to test it)
2. Enclose the product (the original model) with four plastic plates or wooden plates.
3. Mixing part A and part B with 1:1 mixing ratio and stir evenly. And get the mixture for vacuum-pumping. (If there is no vacuumizer, you can just pour the mixture slowly from the corner so that less bubbles caused)
4. Pour the mixture into the model frame.
After about 2-4 hours, when the silicone cured, get out the original model, and there you get a finished addition cured silicone mold .
SHELF LIFE:
Twelve (12) months from date of shipment when stored at 24℃ in original unopened packages.
For further information, please feel free to contact Mandy
TEL: 086-755-89948019
FAX: 086-755-89948030
MOBILE 189-3886-1892
Website: www(dot)szrl(dot)net
E-MAIL: hyjd((at)szrl.net
hyjmandy (at)hotmail(dot)com
|
| Placement Date: |
Sep 27, 2012 |
| Expiration Date: |
Sep 27, 2013 |
|
|
|
|
|
|
Company Name: |
Shenzhen Hong Ye Jie Technology CoLtd |
| Contact Person: |
mandy |
| City: |
shenzhen |
| Country: |
China
 |
| Local Time: |
|
| E-mail: |
Premium
Membership Required (Join Free Today) |
|
| Introduction: |
Hong Kong Hong Ye Ltd. was established in 1998, is a Science and technology corporation which is engaged in production, R & D, and sales of silicone rubber. It sets up Hong Kong Hongye Ltd., Shenzhen Hongye silicone rubber Factory and other affiliated enterprises in 2005.
Our products including 36 series in hundreds of kinds of silicone products like silicone rubber, RTV-2 molding silicone rubber, silicone rubber for manual model design,shoe sole mold silicone rubber,silicon oil, pad printing silicone rubber, encapsulant and potting compound, silicone rubber for LED display, electronic thermolysis ointment, thermal conductivity silicone, special silicone rubber for CPU, silicone tube, silicone membrane, silicone sealant , liquid silicone rubber, addition cure RTV silicone rubber, HTV silicone rubber, solid silicone rubber, gross rubber, silicone rubber sheet, hot stamping silicone plates, hot stamping silicone roller,etc. These are currently been exported to Southeast Asia, Europe, the America and other 50 countries and regions.
To reach the internationally leading quality standard with competitive price is our permanent pursuit. We aim at supply high quality products to meet customers\' satisfaction. It is our solemn commitment that any of our products with quality problems will be replaced within 3 months after purchase. We offer on-site follow-up service for product demonstration, free customer service to solve technical issues, free mold opening technologies, free technical training on pad printing silicon usage and rubber head making. What you need is what we pursue. We are committed to back you up in producing first class products.
Customers and distributors from around the world are welcomed to negotiate with us for business cooperation. Let\'s join hands and strive for mutual prosperity.
Factory location
Building A, No.3, Hongling First Road, Liulian Shibi, Pingdi Town, Long Gang district, Shenzhen, Guangdong
Management Certification: ISO 9000/9001/9004/19011: 2000
|
| Business Type: |
Manufacturer |
| Areas of Interest: |
1. Chemicals/Rubber
|
|
