|
|
|
|
|
|
|
[Sell]
AMWEI PTC Thermistor for Lighting Time Delay and Switching Starting Application |
 |
|
Lighting Switching PTC Thermistor Description
Lighting Switching PTC Thermistor are used when a load in series with the PTC thermistor has to be switched off after a time delay and when switching occurs frequently.
A typical application of switching PTC thermistor is the preheating of electrode in energy-saving lamps or fluorescent lamps. Switching PTC can also be used as a power resistor for loading a capacitor, for example in power supplies or in control units of production equipment.
Lighting Switching PTC thermistor Application
It's applicable to various types of fluorescent lamp, electronic ballast and electronic energy-saving lamp. The PTC can be connected across the lamp resonator without changing the circuits. It can change hard start of the ballast and electronic energy-saving lamp to preheated start and the preheating time of the filament can come up to 0.4-2 seconds, which will extend the service life of the fluorescent tube by over 4 times. |
|
» Posted by: AMWEI Thermistor [China]  |
|
|
|
|
|
[Sell]
AMWEI PTC Thermistor for Telecom Over-current Protection |
|
|
Telecom PTC Thermistor Description
This series of ceramic PTC (positive temperature coefficient ) thermistors help provide protection against power cross, power induction surges and lighting surge defined in ITU, Telcordia, UL. Available in chip, radial-leaded coated and non-coated, SMD, twin vertical surface mount configuration. PTC thermistor overcurrent protector provides reversible, self-resetting protection against over-currents of telecommunication line protector units, improve the reliability of custom premises and network equipment.
Ceramic PTC thermistors can be found providing re-settable line protection at the exchange, monitoring hot spots and protecting ringers, battery feeds, transformers and relay circuits. Also used extensively to protect the mobile phone's battery pack against overcharging in land-based and radio mobile communications.
Advanced developments in telecom equipment in recent years have radically altered the protection requirements of both exchange and subscriber equipment. The PTC thermistor must protect the telephone line circuit against overcurrent, which may be caused by the following examples:
Surges due to lighting strikes on or near to the line plant.
Short-term induction of alternating voltage from adjactent power lines or railway systems, usually caused when these lines or systems develop faults
Direct contact between telephone lines and power lines.
To provide good protection under such conditions, a PTC thermistor is connected in series with each line, usually as secondary protection; However, even with primary line protection (usually a gas discharge tube), the PTC thermistor must fulfill severe requirements.
Surge pulses of upto 2KV can occur and in order to withstand short term power induction, the PTC thermistor must withstand high voltages. If the line has primary protection, a 220V to 300V PTC thermistor is adequate. Without primary protection, 600V PTC device is necessary. We can manufacture a series of PTC thermistor fulfilling both requirements.
Typical Application of PTC Thermistor in Telecommunication Protection
Central Office Switching Equipment (C.O): analog and digital line cards, POTS, T1/E1 equipment, xDSL modems and splitters, multiplexers, CSU/DSU, servers.
Primary Protection Modules: MDF (main distribution frame) modules, network interface devices (NIC).
Custom Premises Equipment, also known as subscriber terminal equipment (T.E.), IT equipment: Modem, phone sets, fax machines, phone wall outlet (plugs), alarm systems, answering machine, PBX systems, ADSL Splitters, internet appliance, POS terminals.
Access Network hardware, LAN WAN equipment, Powered Ethernet systems, VoIP (voice over IP equipment), integrated voice data (IVD), Set-top box (S.B), etc.
Telecom PTC Thermistor Features
Compliant with ITU-T K20 K21 K45
--Basic level lightning surges (10/700μs)
--Basic level power Induction (600V,1A,0.2S)
--Power contact criteria A/B (230V,15min.)
Suitable for continuous connection to main voltage 110/230 VAC in tripped (high ohmic) condition.
Round leadless disk thermistor availble for combined usage of PTC and primary protection, e.g gas arrestor.
Matching available with narrow resistance tolerance.
Tight resistance tolerance maintained after switching.
Negligible resistance drift after soldering or switching. |
|
| » Posted by: AMWEI Thermistor [China] |
|
|
|
|
|
[Sell]
AMWEI Inrush Current Limiting Power NTC Thermistors |
|
|
Power NTC thermistor can be a cost effective device to limit the amount of inrush current in a switching power supply or other devices when the power is first turned on. Power NTC thermistor limits surge current by functioning as a power resistor which drops from a high cold resistance to a low hot resistance when heated by the current flowing through it.
Inrush-current limiters power NTC thermistor protect circuits from undesirably high currents, suppressing high inrush current surges, while its resistance remains negligible low during continuous operation. Thanks to their low resistance in the operating state, Power thermistor have a considerably lower power dissipation than the fixed resistors frequently used for this application.
Inrush Current Limiting Power NTC Thermistor Application
limiting surge current, suitable for the protection of switch mode power supply, UPS power, transformers, motors, various electric heating utensil, energy saving lights, ballast, various power circuit, amplifiers, colored displayer, monitors, color TV, filament protection, etc.
Power thermistor components can also be used for the soft starting of motors, for example in vacuum cleaners with continuous currents of up to 20 A.
Inrush Current Limiting Power NTC Thermistor Advantages:
Low cost solid state device for inrush current supression.
Minimise line current distortion and radio noise.
Protect switches, rectifier diodes and smoothing capacitors against premature failures.
Prevent fuse from blowing in error.
Inrush Current Limiting Power NTC Thermistor Features:
Resin coated disk thermistor with uninsulated lead-wires.
Suitable for both AC and DC circuits up to a voltage of 265 V(rms).
Wide range of resistance, current and dimension.
Excellent mechanical strength.
Suitable for PCB mounting. |
|
| » Posted by: AMWEI Thermistor [China] |
|
|
|
|
|
[Sell]
Fused Sillica Windows |
|
|
Fused Sillica Windows
Fused silica is formed by chemical combination of silicon and oxygen. Advantages of fused silica material include good UV and IR transmission, low thermal expansion, providing stability and resistance to thermal shock over large temperature excursions, wider thermal operating range and high laser damage threshold. Used for windows, lenses, prisms and mirror substrates.
Specifications:
Material: UV grade Fused Silica
Dimension Tolerance: +0.0, -0.1mm
Thickness Tolerance: ± 0.1mm
Surface quality: 60/40(Standard), 10/5(High Precision)
Clear Aperture: >85%
Flatness: λ(Standard), λ/10(High Precision) per 25mm@633nm
Parallelism: 1' (Standard), 10" (High Precision)
Bevel: <0.25mm X 45°
Coating: Upon requirement
Typical Sizes:
Round Shape
Diameter(mm): Φ5.0；Φ10.0 ；Φ12.7；Φ15.0；Φ20.0；
Φ25.4；Φ30.0；Φ38.1；Φ50.8；Φ76.2
Square Shape:
WxH(mm) 5.0x5.0 ；10.0x10.0 ；15.0x15.0 ；
20.0x20.0；25.0x25.0；50.0x50.0
Thickness(mm): 0.5；1.0；1.5；2.0；3.0；
4.0；5.0；6.0；8.0；10.0
How to order Windows?
Example:
Material:N-BK7
Diameter:Φ25.4+0.0/-0.1mm
Thickness:1.0±0.1mm
Surface quality: 60-40 S/D
Flatness: λ/2 per 25mm @633nm
Paralelism: <1 arc minute
Coating:Both side AR,R<0.25% @1064nm, AOI=0°
Beamsplitter Cubes
Beamsplitter Plates
Polarization Beamsplitters
Beam Splitting coating
Dielectric High Reflection Coating
Dual-Wavelength Anti-reflection coating
Metallic High Reflection Coating
Multilayer Broadband Anti-reflection Coating
MultiLayer Sharp “V” Anti-reflection coating
Partial Reflection Coating
Single Layer MgF2 Anti-reflection Coating
Cr4+YAG Crystal
KTP crystal
Nd YAG Crystal
Bandpass Filters
Birefringent Filters
Colored glass Filters
Achromatic Lenses(Doublets)
Ball Lenses
Bi-Concave Lenses
Bi-Convex Lenses
Meniscus Lenses
Plano-Concave Cylindrical Lenses
Plano-Concave Lenses
Plano-convex Cylindrical Lenses
Plano-Convex Lenses
Powell Lenses
Rods Lenses(Light pipes)
B-270
BK7 Glass
Float Glass
Fused Silica
Dielectric Mirrors
Hot&Cold Mirror
Metallic Coated Mirrors (Al, Ag, Au)
Corner retroreflectors(Corner Cube Prisms)
Dove Prisms
Equilateral Dispersing Prisms
Penta Prisms
Right Angle Prisms
Special prisms
Wedge Prisms
Multiple order Waveplates
True Zero order Waveplates
Zero order Waveplates
BK7 Windows
CaF2 Windows
Fused Sillica Windows
Ge Windows
MgF2 windows
Sapphire Windows
Si Windows
optical windows
optical lenses
optical prisms
optical beamsplitters
optical mirrors
optical filters
optical waveplates
optical crystals
optical coating
|
|
| » Posted by: [] |
|
|
|
|
|
[Sell]
Dielectric Mirrors |
|
|
Dielectric Mirrors
Dielectric Mirrors offer near total reflection, minimizing losses in nearly all optical systems. These coatings are very durable, easily cleaned, and resistant to laser damage.
Available either broadband or narrowband, they operate efficiently over 0–45°angle of incidence: AOI=0°, R>99.8%;
AOI=45°, R>99.5% (Rs>99.9%, Rp>99.2%).
Specifications:
Material: N-BK7 or UV Fused Silica
Dimension Tolerance: +0.0, -0.1mm
Thickness Tolerance: ± 0.1mm
Surface quality: 60/40(Standard), 10/5(High Precision)
Clear Aperture: >85%
Flatness: λ/4 per 25mm@633nm
Parallelism: <1'
Bevel: <0.25mm X 45°
Coating: One surface(S1) :HR @ design wavelength
The other surface :uncoated
Typical Sizes:
Size(mm) Size(mm)
Φ5.0x1.0 10.0x10.0x3
φ10.0x2.0 20.0x20.0x3
Φ12.7x2.0 25.4x25.4x3
Φ15.0x3.0 30.0x30.0x5
other sizes and shapes are available.
|
|
| » Posted by: [] |
|
|
|
|
|
[Sell]
Colored glass Filters |
|
|
Cut-off type colored optical filter glass
The glass is named based on spectral characteristic of which is represented by the wavelength transmission limit. For example, if the transmission limit of glass is 490nm,then it is named as JB490.There are five groups and 35types glasses.
Selective absorption colored optical filter glass
This part of the glasses can be divided into 14 kinds and 78 types based on the color and application in this catalogue. The types are arranged in accordance with serial numbers, which have no special meaning.
Neutral filter glass
They are named based on the average transmissivity characteristics in 400nm to 700nm wavelength with 2mmthick sampler is 70%,then it's named as ZAB70.And there are ten types of glasses in this part. But three types of them(ZAB65,ZAB30,ZAB5)are tested in 440nm-660nm wavelength.
Specifications:
Material: Color glass
Dimension Tolerance: +0.0, -0.2mm
Thickness Tolerance: ±0.2mm
Surface quality: 80/50
Clear Aperture: >85%
Flatness: 1 λ per 25mm@633nm
Parallelism: ±3'
Bevel: <0.25mm X 45°
Coating: Upon requirement
Typical Sizes:
Size(mm) Size(mm)
Φ5.0x1.0 Φ20.0x3.0
φ10.0x2.0 Φ25.4x3.0
Φ12.7x2.0 Φ50.8x3.0
Φ15.0x3.0 Φ76.2x5.0
Other sizes and shapes are available.
|
|
| » Posted by: [] |
|
|
|
|
|
[Sell]
Birefringent Filters |
|
|
Birefringent filter is made by crystal quartz. It's used in the laser cavity for wavelength selection. We can provide different thickness birefringent filter for our customer's laser applications.
Specifications:
Material: Crystal quartz
Dimension Tolerance: +0.0, -0.2mm
Thickness Tolerance: ± 0.02mm
Surface quality: 20/10
Clear Aperture: 90% of the central area
Parallelism: <5 arc sec
|
|
| » Posted by: [] |
|
|
|
|
|
[Sell]
Bandpass Filters |
|
|
Bandpass filter plate are divided into short-pass and long-pass filters according to whether they transmit below or above the transition wavelength. The transition wavelength or cut-on/off wavelength is the wavelength at which the transmission is 50% of its peak value.
Specifications:
Material: N-BK7 ;Fused silica
Dimension Tolerance: +0.0, -0.1mm
Thickness Tolerance: ±0.1mm
Surface quality: 60/40
Clear Aperture: >85%
Parallelism: λ /4 per 25mm@633nm
Bevel: ±3'
Coating: One surface(S1) :HR & HT
The other surface(S2):Upon requirement
|
|
| » Posted by: [] |
|
|
|
|
|
[Sell]
Nd: YAG Crystal |
|
|
Neodymium Doped Yttrium AIuminum Garnet (Nd: YAG) Crystal
Nd: YAG crystal is the most widely used solid-state laser material today. Now, we are able to stably supply quantity of Nd: YAG rods with high optical homogeneity, consistent performance, high processing accuracy and on time delivery.
1. Basic Properties (1.0 atm% Nd doped)
Chemical Formula Nd:Y3Al5O12
Crystal Structure Cubic
Lattice Constants 12.01 Å
Concentration ~ 1.2 x 1020 cm-3
Melting Point 1970 oC
Density 4.56 g/cm3
Mohs Hardness 8.5
Refractive Index 1.82
Thermal Expansion Coefficient 7.8 x 10-6 /K [111], 0 - 250 oC
Thermal Conductivity 14 W/m /K @20 oC, 10.5 W /m /K @100 oC.
Lasing Wavelength 1064 nm
Stimulated Emission Cross Section 2.8x10-19 cm-2
Relaxation Time of Terminal Lasing Level 30 ns
Radiative Lifetime 550 ms
Spontaneous Fluorescence 230 ms
Loss Coefficient 0.003 cm-1 @ 1064 nm
Effective Emission Cross Section 2.8 x 10-19 cm2
Pump Wavelength 807.5 nm
Absorption band at pump wavelength 1 nm
Linewidth 0.6 nm
Polarized Emission Unpolarized
Thermal Birefringence High
2. Standard Products specification
Dopant Concentration (atomic %): 0.9%~ 1.1%
Orientation: <111> crystalline direction (±5o)
Wavefront distortion:l/8 per inch, measured by a double-pass interferometer @ 633 nm
Extinction Ratio:
Rods with diameter from 3 mm to 6.35 mm and with length to 100 mm:>30dB
Rods with diameter from 7 mm to 10 mm and with length to 100 mm:>28dB
Dimension Tolerances
Rods with diameter: ±0.025 mm (±0.001"), Length: ±0.5 mm (±0.02")
Barrel Finish:50 80 micro-inch (RMS) , grooved rod barrel are also available
Ends Finish:
Surface Figure: <l/10 @ 633 nm
Parallelism: < 10 arc seconds
Surface quality:< 5 arc minutes
Clear Aperture: > 10/5 Scratch / Dig per MIL-O-1380A
chamfer:<0.1 mm @ 45°
clear Aperture: extend over the entire faces to the chamfered edges
Anti-Reflection Coating:
Single layer MgF2 coating with high damage threshold for high power laser operation. Reflectivity R < 0.25% @ 1064 nm per surface. Damage threshold over 750 MW/cm2@ 1064nm, 10 ns and 10 HZ.
High-Reflection Coating:
Standard HR coating with R>99.8% @ 1064nm and R<5% @ 808nm can be performed in WTS. Other HR coatings, such as HR @ 1064/532 nm, HR @ 946nm, HR 1319 nm and other wavelengths are also available.
Standard products in-stock:
The standard Nd: YAG laser rod with dimension of f3x5 mm and f4x50 mm with AR or HR- coating for Diode Pumped Solid State Lasers (DPSS) are ready for immediate delivery. For more information about standard Nd: YAG rods please refer to page 62 of Diode Pumped Laser Optics Kits.
Note:Higher grade or specific Nd: YAG rods or slabs are also available upon request.
|
|
| » Posted by: [] |
|
|
|
|
|
[Sell]
KTP crystal |
|
|
Potassium Titanyl Phosphate (KTiOPO4 or KTP)
Advantages:
Large Nonlinear Optical (NLO) Coefficients
Wide Angular Bandwidth and Small Walk-off Angle
Broad Temperature and Spectral Bandwidth
High Electro-Optic (E-O) Coefficient and Low Dielectric Constant
Large Figure of Merit for an Optical Waveguide Modulator
Nonhygroscopic, Good Chemical and Mechanical Properties
Applications:
Frequency Doubling (SHG) of Nd-doped Lasers for Green/Red Output.
Frequency Mixing (SFM) of Nd Laser and Diode Laser for Blue Output.
Parametric Sources (OPG, OPA and OPO) for 0.6mm-4.5mm Tunable Output.
E-O Modulators, Optical Switches, Directional Couplers.
Optical Waveguides for Integrated NLO and E-O Devices.
DND Provides:
Standard size of KTP crystal for DPSS application;
Strict Quality Control;
2 - 3 Weeks Delivery;
Unbeatable Price and Special OEM Discount;
Free Technical Support;
AR-Coating, Mounting and Re-polishing Service;
Mass Production to Support Industrial and Commercial Applications;
New: Precision Oven εt Temperature Controller for Heating KTP.
Basic Properties
1. Structural and Physical Properties
Crystal Structure Orthorhombic, point group mm2
Cell Parameters a = 6.404Å, b = 10.616Å, c = 12.814Å Z = 8
Melting Point 1172 oC Incongruent
Curie point 936 oC
Mohs Hardness » 5.0
Density 3.01g/cm3
Linear Absorption Coefficients a <0.001 cm-1 @ l =1064 nm or 532 nm
Hygroscopic Susceptibility no
Relative Dielectric Constant eeff=13
Specific heat 0.1643 cal/g.oC
Electrical conductivity 3.5x10-8 s/cm (c-axis, 22oC, 1KHz)
Thermal Conductivity 13W/m/K
2. Linear Optical Properties
Transparency Range:
350 - 4500 nm, See Transparency Curve
KTP Transparency Curve
Refractive Indices:
Wavelength nx ny nz
1064 nm 1.7377 1.7453 1.8297
532 nm 1.7780 1.7886 1.8887
Therm-Optic Coefficients:
dnx/dT=1.1x10-5/oC
dny/dT=1.3x10-5/oC
dnz/dT=1.6x10-5/oC
Sellmeier Equations:
n2x=3.0065+0.03901/(l2-0.04251)-0.01327l2
n2y=3.0333+0.04154/(l2-0.04547)-0.01408l2
n2z=3.3134+0.05694/(l2-0.05658)-0.01682l2
3. NonLinear Optical Properties
Phase-Matchable Output Range: 492- 1700 nm
NLO Coefficients:
d31=2.54pm/V, d32=4.35pm/V, d33=16.9pm/V
d24=3.64pm/V, d15=1.91pm/V at 1064 nm
deff(II)» (d24 - d15)sin2fsin2q - (d15sin2f + d24cos2f)sinq
Electro-Optic Coefficients: Low Frequency (pm/V) High Frequency(pm/V)
g13 9.5 8.8
g23 15.7 13.8
g33 36.3 35.0
g51 7.3 6.99
g42 9.3 8.8
Applications for SHG and SFG of Nd: lasers
KTP is the most commonly used material for frequency doubling of Nd: YAG lasers and other Nd-doped lasers, particularly at the low or medium power density. The following Table lists the major NLO properties of KTP for frequency-doubling of Nd: YAG laser.
PM angle q=90o, f=23.5o,
where q & f are polar angles referring to Z and X.
Effective SHG coefficient deff » 8.3xd36(KDP)
Angular acceptance 20 mrad-cm
Temperature acceptance 25oC-cm
Spectral acceptance 5.6 Å-cm.
Walk-off angle 4.5mrad (0.26o)
Optical damage threshold > 450MW/cm2, (@ 1.06mm, 10ns, 10Hz)
To date, extra- and intra-cavity frequency doubled Nd: lasers using KTP have become a preferred green laser source for many R&D, medical, industrial and commercial applications. By using extracavity KTP SHG, over 80% conversion efficiency and 700mJ green laser were obtained with a 900 mJ jection-seeded Q-switched Nd: YAG laser.
Type II SHG in XY Plane Type II SHG in XZ Plane
Applied to diode-pumped Nd: laser, KTP is a basic NLO crystal for the construction of compact visible solid state laser systems. Recent advances in intracavity-doubled Nd: YVO4 and Nd: YAG lasers have increased the demand for compact green lasers used in display, construction, optical disk and laser printer. Over 200 mw TEM00 green outputs are available from LD pumped Nd: YVO4 and Nd: YAG lasers and 3 W TEM00, mode-locked green laser was generated by intracavity SHG in a 5 |
|
| » Posted by: [] |
|
|
|
|
|
[Sell]
Cr4+:YAG Crystal |
|
|
Chromium Doped Yttrium Aluminum Garnet Cr4+:YAG Crystal
A High Power, Solid State and Compact Passive Q-switch
Passive Q-Switching is preferred for simplicity of manufacturing and operation, low cost and reduced system size and weight. Cr4+: YAG (Y3Al5O12) is an excellent crystal for passively Q-switching diode pumped or lamp-pumped Nd: YAG, Nd: YLF, Yb: YAG or other Nd and Yb doped lasers at wavelength from 1.0 to 1.2 mm. Because of its chemically stable, durable, UV resistant, good thermal conductivity and high damage threshold (> 500 MW/cm2) and being easy to be operated, it will replace traditional materials, such as, LiF, organic Dye and color centers.
Basic Properties of Cr4+:YAG
Formula Cr4+:Y3Al5O12
Crystal Structure Cubic Garnet
Dopant Level 0.5 mol% ~ 3 mol%
Hardness 8.5 (Mohs)
Damage Threshold > 500 MW/cm2
Refractive Index 1.82 @ 1064 nm
Main Specifications
Flatness < λ/8
Wavefront Distortion λl/4
Parallelism < 30”
Surface quality 20/10 scratch/dig
AR-coating R<0.2% @ 1064 nm
Standard Aperture 3X3 ~ 10X10 mm
AR-coatings and HR-coatings are also available. We can control the initial transmission (To) from 10% to 95% according to customer’s requirements. The preliminary experiments of WTS's Cr4+: YAG showed that the pulse width of passively Q-switched lasers could be as short as 9 ns for diode pumped Nd: YAG lasers and repetition as high as 10 kHz for diode pumped Nd: YVO4 lasers. Furthermore, an efficient green output at 532 nm, and UV output at 355 nm and 266 nm were generated, after a subsequent intracavity SHG in KTP for diode pumped and passive Q-switched Nd: YAG and Nd:YVO4 lasers.
Cr4+: YAG is also a laser crystal with tunable output from 1.35 mm to 1.6 mm. It can generate ultrashort pulse laser (to fs pulsed) when pumped by Nd: YAG laser at 1.064mm.
Note: When ordering Cr4+: YAG crystal, please specify the aperture, initial transmission (To) and coatings.
|
|
| » Posted by: [] |
|
|
|
|
|
[Sell]
Single Layer MgF2 Anti-reflection Coating |
|
|
Magnesium fluoride(MgF2) is probably the most widely used thin film material for optical coatings. Its performance is not outstanding but represents a significant improvement over an uncoated surface. It is the most commonly used, low-cost anti-reflection coating, and widely used in Lens & Prism, Input & output surface.
|
|
| » Posted by: [] |
|
|
|
|
|
[Sell]
Partial Reflection Coating |
|
|
Single Wavelength Partial Reflective Coating
When a narrow wavelength radiation is incident on Single wavelength partial reflective coating, part of the radiation is reflected and the other part is transmitted. This coating always show a high reflectivity for S-polarization radiation and high transmission for P-polarization radiation. The main application of this coating is for a beamsplitter with 45 angle of incidence. It is the most commonly used, low-cost anti-reflection coating, and widely used in Lens & Prism, Input & output surface.
Broadband Wavelength Partial Reflective Coating
Broadband Wavelength Partial Reflective coating has similar performance to that of Single Wavelength Partial Reflective coating. However, Broadband Wavelength Partial Reflective coating can split the incident radiation over a wide spectrum, not Single Wavelength Partial Reflective. It can be widely used to split the incident radiation over a wide spectrum.
|
|
| » Posted by: [] |
|
|
|
|
|
[Sell]
MultiLayer Sharp “V” Anti-reflection coating |
|
|
It can reach the lowest reflectivity at a center wavelength, and is widely used in single laser wavelength or multiple, closely spaced wavelength system.
|
|
| » Posted by: [] |
|
|
|
|
|
[Sell]
Beamsplitter Cubes |
|
|
Beamsplitter Cube is a more sophisticated type consisting of two right- angle prismscemented together at their hypotenuse faces.The cemented face of one prism is coated.Before cementing, with a metallic or dielectric layer having the desired reflecting properties, both in the percentage of reflection and the desired color. The absorption loss to the coating is minimal and transmission and reflection approach 50%.
Specifications:
Material: BK7 grade A optical glass
Dimension Tolerance: +0.2, -0.2mm
Thickness Tolerance: ±0.2mm
Surface quality: 60/40
Clear Aperture: >85%
Flatness: λ/4 per 25mm@633nm
Parallelism: ±3'
Bevel: <0.25mm X 45°
Coating: Hypotenuse surface :Partial reflective coating
Entrance/Exit surfaces :AR coating
Reflectance/Transmittance R/T=50/50% ±5% ;
Other ratio is available
( R,T are the average of S- and P-pol) ,AOI= 0°
Typical Sizes:
Size(mm) Size(mm)
5.0x5.0x5.0 18.0x18.0x18.0
10.0x10.0x10.0 20.0x20.0x20.0
12.7x12.7x12.7 25.4x25.4x25.4
15.0x15.0x15.0 30.0x30.0x30.0
|
|
| » Posted by: [] |
|
|
|
|
|
[Sell]
Sell Capacitor CBB65 |
|
|
The capacitor takes heavy-edge metallized Al/Zn film as electrodes and dielectric. The elements are tight winded by high-velocity winders and canned in aluminum cases. Refined castor oil is adopted as impregnation agent treated in vacuum and high temperature condition. Those make a more reliable performance and longer lifespan for a capacitor. Meanwhile the second generation of mechanical anti-explosion design is selected as blast-proof secure measure for our capacitors. The reliability is more affirmatively enhanced.
Applications:
Broadly applied to starting and running of AC single-phase motors at 50Hz(60Hz) frequency for family air conditioners and high power illuminators for the sake of power factor compensation.
Technical Specifications:
Standard：IEC 60252-1:2001
Technical features：
Climate type：40/70/21 or 40/85/21
Capacitance tolerance：± 5%
I.R：≥3000S（MΩ·µF）
Dielectric dissipation factor：tgδ≤0.002 (50Hz～100Hz)
Application requirements：
Altitude：≤2000m
Residual voltage while loading: less than 10% of rated voltage.
Allowed maximum voltage: less than 1.1 times of rated voltage
Permissible maximum current: less than 1.3 times of rated current.
Dimensional specification (mm)
Related voltage 200,250,370,400,440,450,600,700,1200VAC
Capacitance 1--100uf
D 40,45,50,55, 60,63.5, 52*32,71*45
H 60,65,70,75,80,85,90, 95,100,105,110,115, 120,125,135,138
|
|
| » Posted by: Anhui Safe Electronics Co.Ltd [China] |
|
|
|
|
|
[Sell]
Sell Capacitor CBB61 |
|
|
The capacitor takes heavy-edge metallized Al/Zn film as electrodes and dielectric. It is impregnated with flame-retardant epoxy resin and canned in cubic ABS or PBT plastic case with characteristics of small size, reliable performance and long endurance.
Applications:
Broadly applied to starting and running of AC single-phase motors at 50Hz(60Hz) frequency for air conditioners' fans, electric fans and exhaust fans etc. at comparatively low rated power.
Technical Specifications
Standard：IEC 60252-1:2001
Technical features：
Climate type：40/70/21 or 40/85/21
Capacitance tolerance：± 5%
I.R：≥3000S（MΩ·µF）
Dielectric dissipation factor：tgδ≤0.002 (50Hz～100Hz)
Application requirements：
Altitude：≤2000m
Residual voltage in application: less than 10% of rated voltage.
Allowed maximum voltage: less than 1.1 times of rated voltage
Permissible maximum current: less than 1.3 times of rated current.
Dimensions & specifications (mm)
Related voltage 200,250,370,400,440,450,600,700,1200VAC
Capacitance 1--100uf
L 31,37,38,47,48,58
W 14,17,18,21,22,26,34
H 24,27,28,29,31,34,38,40,44,52
|
|
| » Posted by: Anhui Safe Electronics Co.Ltd [China] |
|
|
|
|
|
[Sell]
Sell Capacitor CBB60 |
|
|
　The capacitor takes heavy-edge metallized Al/Zn PP film as electrodes and dielectric. Its components are sealed with flame-retardant epoxy resin. It has cylindrical outline with high moisture resistance and stability.
Applications
Broadly applied to starting and running of AC single-phase motors at 50Hz(60Hz) frequency for washers and high efficiency compressors of refrigerators etc.
Technical Specifications
Standard：IEC 60252-1:2001
Technical features：
Climate type：40/70/21 or 40/85/21
Capacitance tolerance：± 5%
Insulation Resistance：≥3000S（MΩ·µF）
Dielectric dissipation factor：tgδ≤0.002 (50Hz～100Hz)
Application requirements：
Altitude：≤2000m
Residual voltage in application :less than 10% of rated voltage.
Allowed maximum voltage: less than 1.1 times of rated voltage
Permissible maximum current: less than 1.3 times of rated current
Dimensions & specifications (mm)
Related voltage 200,250,370,400,440,450,600,700,1200VAC
Capacitance 1--100uf
D 30,32,35,40, 41,43,45,46, 50
H 47,57,65,73,80,84,85,98,105,110
|
|
| » Posted by: Anhui Safe Electronics Co.Ltd [China] |
|
|
|
|
|
[Sell]
polycrystalline silicon solar cells 10W |
|
|
Technical parameter (with tolerance -/3%)
Maximum power(W) 10W
Open circuit voltage(Voc) 21.52v
Optimum operating voltage(Vmp) 17.6v
Short circuit current(Isc) 0.67A
Optimum operating current(Imp) 0.56A
Solar cell 156*14mm Poly
Qty of cell and connections: 36(2*18)pcs
Size of module(mm): 360*335*30mm
Weight: 1.2kg
Limits
Operating temperature -40 to +85℃
Maximum system voltage 715VDC
Temperature and coefficients
NOCT 46℃±2℃
Current temperature coefficient %/K 0.06±0.01
Voltage temperature coefficient mV/K -(165±10)
Power temperature coefficient %/K -(0.5±0.05) |
|
| » Posted by: ADD Solar Energy Group Co.,Ltd [China] |
|
|
|
|
|
[Sell]
Start capacitor (capacitor, starting capacitor, compressor parts, HVAC/R parts, refrigerator parts) |
|
|
| Type Aluminum electrolytic capacitor for starting AC motor adopts aluminum foils as electrode, alumina as dielectric non olid electrolyte and adopts metal, Bakelite resin or engineering plastic ,aluminum as cases and lug, wire or cable as terminals. This series of capacitors is bipolarized, and is widely used it applies to AC single phase motor with frequency 50/60Hz.It can help motors gain high torque with low starting current and make motors start normally . It can also apply to refrigerators and compressors of air conditioner and etc |
|
| » Posted by: Kanpus Refrigeration Co., Limited [China] |
|
|
|
|
|
«back
Pages: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 next»
|
|
|
