|
|
|
|
|
|
|
[Sell]
E625Addition Molding Silicone rubber |
 |
|
HY- E625Addition Molding Silicone rubber
Description:
HY-E625# addition molding silicone is generally named two-components silicone rubber, Part A is a flowable liquid, part B is the curing agent. It features an exceptional fluidity and good operability. The mixing ratio is 1:1, mainly be suitable for making molds application.
Applications:
HY- E625# addition molding silicone could be mainly used for making concrete stones, precision molds, PU molds, for life casting, fabric finishing, shoe soles making， seal for electronic components and solar circuit board, trademark decoration. etc.
Technique Data:
Model HY-E625#
Appearance Translucent
Mixing Ratio 1:1
Operating time (Mins 25°C) 30 - 50
Curing time (Mins 25°C) 120 - 240
Curing time (Mins 60°C) 20 - 30
Hardness (A°) 25±2
Density ( g/cm 3 ) 1.08
Viscosity (CS) (Part A) 30000 ± 5000
Viscosity (CS) (Part B) 5000 ± 500
Viscosity (CS) (After mixed) 10000 ± 2000
Tensile-strength( kgf /cm2 ) 50± 5
Tear-strength (kgf /cm2 ) 15 ± 2
Elongation-break(%) 500 ± 50
Retractility(%) ≤0.1
OPERRATING INSTRUCTION:
1. Clean your products and brush a layer of release agent (detergent or soap water) on the surface of your product.
Note: The model should not have been used to make molds for tin cured silicone rubber before. Otherwise, the addition silicone will not get cured. (Use a new model to test it)
2. Enclose the product (the original model) with four plastic plates or wooden plates.
3. Mixing part A and part B with 1:1 mixing ratio and stir evenly. And get the mixture for vacuum-pumping. (If there is no vacuumizer, you can just pour the mixture slowly from the corner so that less bubbles caused)
4. Pour the mixture into the model frame.
After about 2-4 hours, when the silicone cured, get out the original model, and there you get a finished addition cured silicone mold .
SHELF LIFE:
Twelve (12) months from date of shipment when stored at 24℃ in original unopened packages.
For further information, please feel free to contact Mandy
TEL: 086-755-89948019
FAX: 086-755-89948030
MOBILE 189-3886-1892
Website: www(dot)szrl(dot)net
E-MAIL: hyjd((at)szrl.net
hyjmandy (at)hotmail(dot)com
|
|
» Posted by: Shenzhen Hong Ye Jie Technology CoLtd [China]  |
|
|
|
|
|
[Sell]
Silicone Rubber for building decoration Mold |
|
|
Silicone Rubber for building decoration Mold Making (Tin catalyst series)
Detailed Product Description
Applications of Silicon rubber for decoration mold making
Silicon rubber for building decoration molding making is primarily intended for poly resin crafts, PU crafts, PU resin crafts ,gypsum crafts ,unsaturated resin crafts, lighting and candles crafts ,plastic toy , gifts crafts industry, a large statue Buddha, furniture relievo, furniture decorative materials, statues Buddha, artifacts copied, building decoration materials, large-scale cement mold, artificial fossils Factory, Europe component factory, simulation landscapes, animals and plants sculpture, sandstone crafts and so on.
Features of Silicon rubber for decoration mold making
Silicon rubber for building decoration mold making is a kind of white or red flowing liquid with general hardness of 22-50A°after curing. Molding silicon rubber is a kind of elastic silicon rubber mold which features with resistance to deformation, high-temperature, acid-alkali and expansion as well as high reproduction times, good elongation, good tensile and tear strength.
Operations of Silicon rubber for decoration mold makin
If the customer wants to make products and silicone molds in large size, the mold should be made of silicon rubber with high hardness. On the contrary, if the mold with fine and precise patterns, it should be made of silicon with low hardness. The amount of the curing agent added depends on the actual requirements of the customer. If fast drying and demold is required, more curing agent is needed; contrarily, if slower drying and demold is required, then less curing agent is needed.
(Note: our company does not recommend you to add silicon oil into the silicone rubber. If the products require a special soft silicone mold or have fine detailed and complex patterns, 5% - 10% silicon oil could be added to soften the mold for easy demold.)
For further information, please feel free to contact Mandy
TEL: 086-755-89948019
FAX: 086-755-89948030
MOBILE 189-3886-1892
Website: www(dot)szrl(dot)net
E-MAIL: hyjd((at)szrl.net
hyjmandy (at)hotmail(dot)com
|
|
| » Posted by: Shenzhen Hong Ye Jie Technology CoLtd [China] |
|
|
|
|
|
[Sell]
Gypsum Decorative Line Silicone Rubber |
|
|
Gypsum Decorative Line Silicone Rubber
•Usage: for toy gifts and craftwork gift, products with complex fine details, and made in pouring way.
Description: 　　
•HY-638# silicon rubber is mainly used for toy gifts and craftwork gifts with the advantages of good tensile strength, high tear strength, high temperature resistance, high duplication times and repeated use, etc.
•It is suitable for small products or fine and precision products which is difficult to demould.
•This silicone rubber is one of the products with the highest use level in the production of craftwork gifts and the shrinkage is up to 2‰.
•Applications: poly technique, lightings, candles, and molds in multiple pieces for large products.
RTV-2 molding silicon rubber and silicone rubber are general called two-component room temperature vulcanization silicone rubber with excellent fluidity and good operational performance.
•Add curing agent of 2%-3% at the room temperature, the silicone rubber is still operational within 30 minutes, and in 2-3 hours, an elastic silicon mold will be obtained with resistance to deformation, high-temperature, acid and alkali and expansion.
•The silicone rubber is mainly applicable to mold duplication of poly crafts, resin craftworks, lightings, candles, etc. and fabrication of precision molds.
Operation instruction for RTV-2 molding silicone rubber: 　　
•The product is white or red flowing liquid with general hardness of 22—50A°after curing.
•If the customer wants to make large products and large size molds, the mold should be made of silicone rubber with high hardness.
•On the contrary, if the mold with fine and precision patterns, it should be made of silicon with low hardness.
•The amount of the curing agent depends on the actual requirements of the customer.
•If molds requiring fast drying and demould, more curing agent is needed; contrarily, if molds requiring slower drying and demould, less curing agent is needed.
Note:
•our company does not recommend you to add silicone oil into the silicone rubber.
•If a special soft silicon mold or fine detailed and complex patterns products are required, 5%-10% silicone oil can be added to soften the mold for easy demould.
The proportions and reactions of the curing agent and the silicon are listed as follows: 　　
•Adding curing agent 1%, the silicone can still be operated within 2.5 hours and can be demoulded after 6-8 hours. 　　
•Adding curing agent 2%, the silicone can still be operated within 50 minutes to 1 hour and can be demoulded after 2-3 hours. 　　
•Adding curing agent 3%, the silicone can still be operated within 28 - 30 minutes and can be demoulded after 1.5-2 hours.
•Adding curing agent 4%, the silicone can still be operated within 10 - 15 minutes and can be demoulded.
For further information, please feel free to contact Mandy
TEL: 086-755-89948019
FAX: 086-755-89948030
MOBILE 189-3886-1892
Website: www(dot)szrl(dot)net
E-MAIL: hyjd((at)szrl.net
hyjmandy (at)hotmail(dot)com
|
|
| » Posted by: Shenzhen Hong Ye Jie Technology CoLtd [China] |
|
|
|
|
|
[Sell]
Pad Printing Silicone Rubber |
|
|
Pad Printing Silicone Rubber Features:
Pad printing silicone rubber with high print times and abrasion resistance. Pad printing silicone rubber has good printing effects, permanent and durable. We can provide all kinds of color and our catalyst is free.
Pad Printing Silicone Rubber Operation Instructions:
Pad printing silicone rubber is two-component silicone, part A is liquid silicon rubber, part B is catalyst. The usual mixture of silicone rubber and catalyst is 100: 2 or 100: 3. E.g. we take 100g of liquid silicon rubber and 2g-3g catalyst, mix them and pour it to your mold. A fter 2-4 hours, you will get a Pad printing silicone rubber.
Any questions of this kind of silicone rubber , please feel free to contact Annie :
TEL: 086-755-89948006
FAX: 086-755-89948030
MOBILE:086-18938861891
Website: www(dot)szrl(dot)net
E-MAIL: hyjx@szrl.net
|
|
| » Posted by: Shenzhen Hong Ye Jie Technology Co. Ltd. [China] |
|
|
|
|
|
[Sell]
Manual Molding Silicone Rubber |
|
|
Manual Molding Silicone Rubber
a. Applications of Manual Molding Silicone Rubber
Manual Molding Silicone Rubber is mainly used for model design of manual mold, PVC plastic molds, cement products, low melting point alloy molds, alloy toys, plastic toys, electronics, handicrafts, stationery, large-scale sculpture, reproduction of cultural relic, shoe sole molds, pad printing allocation, Electronic equipment antivibration, etc.
b. Model Codes of Manual Molding Silicone Rubber
HY-528# is applicable to make molds of smaller products and the production will be 2-3 pieces.
HY-540#, compared to other two types, for its moderate hardness and better quality & performance, its production will be 20-30 pieces.
HY-570# is applicable to large size products duplications and Electronic equipment antivibratio
Any questions of Pad Printing Silicone Rubber, please feel free to contact Annie :
TEL: 086-755-89948006
FAX: 086-755-89948030
MOBILE:086-18938861891
Website: www(dot)szrl(dot)net
|
|
| » Posted by: Shenzhen Hong Ye Jie Technology Co. Ltd. [China] |
|
|
|
|
|
[Sell]
RTV 2 silicone rubber make molds for gypsum casting |
|
|
FEATURES of RTV 2 silicone rubber:
1.Two-part of RTV 2 silicone rubber flowable liquid silicon and curing agent.
2.RTV 2 silicone rubber Cures at room temperature within 5-46hours.
3.RTV 2 silicone rubber has An exceptional fluidity and good operability.
4.RTV 2 silicone rubber has good Temperature and deformation resistance as well as low shrinkage.
5.RTV 2 silicone rubber has High duplication times.
Model of RTV 2 silicone rubber:
RTV 2 silicone rubber RTV-630#:
Usage: Silicon rubber for PU/poly resin products,plaster,candles, gypsums crafts, cement products, concrete/architectural products,statuary, casting molds making, etc.
Model 630#
Appearance white
Mixing proportion of curing agent (%) 5%
Operating time (mins 25 0C ) 20-40
Curing time(hours 25 0C) 3-5
Hardness (A°) 30±2
Density ( g/cm 3 ) 1.08
Viscosity (Mpas -25 0C) 21000~23000
Tensile-strength(kgf /cm2 ) ≥40
Tear-strength (kgf /cm ) ≥30
Elongation-break(%) ≥ 450
Retractility(%) ≤0.3
Operations for RTV 2 silicone rubber:
Step One to use RTV 2 silicone rubber: Take 100g of part A and add 2g of part B and mix the silicon rubber and the curing agent evenly.
Step Two to use RTV 2 silicone rubber: vacuum pumping
Without exception, this takes less than 10 minutes. Otherwise, it will cause cross linking reaction, and no more further steps will be available.
Step Three to use RTV 2 silicone rubber: Brushing cast & Perfusion Molding operation.
Frequently asked questions of RTV-2 silicone rubber for mold making
Why does the silicone rubber mold have few molding times?
The silicone rubber mold has few molding times is due to follwoing reasons: adding too much silicone oil which will destroy the molecular of silicone rubber; making the mold for small and fine detailed products with higher hardness silicone rubber which is easy to break; making the mold for large products with soft silicone rubber which will reduce the tensile and tear strength of the mold, and the mold will have deformation. Thus, we should take the proper silicone rubber to make the mold for suitable products.
Any further information required, pls feel free to contact Mr Chris
Tel: 0086-755-89948019
Fax: 0086-755-89948030
Mobile：0086-18938867508
E-mail: hyi(at)szrl(dot)net
|
|
| » Posted by: Shenzhen Hong Ye Jie Technology Co.,Ltd [China] |
|
|
|
|
|
[Sell]
pad printing silicone rubber |
|
|
Brief description:
Pad printing silicone :
1. resistance to deformation, high-temperature
2. high printing times
3. good aging resistance
4. exceptional elasticity
5 great printing effect
Pad Printing Silicone Rubber Usages:
Pad printing silicone rubber is mainly use for printing irregular patterns of plastic toys, electroplating toys and trade makers. Pad printing silicone rubber as a carrier which transfer patterns on the steel plate to the toys products surface.
Pad Printing Silicone Rubber Features:
Pad printing silicone rubber with high print times and abrasion resistance. Pad printing silicone rubber has good printing effects, permanent and durable. We can provide all kinds of color and our catalyst is free.
Pad Printing Silicone Rubber Operation Instructions:
Pad printing silicone rubber is two-component silicone, part A is liquid silicon rubber, part B is catalyst. The usual mixture of silicone rubber and catalyst is 100: 2 or 100: 3. E.g. we take 100g of liquid silicon rubber and 2g-3g catalyst, mix them and pour it to your mold. A fter 2-4 hours, you will get a Pad printing silicone rubber.
Any further information required, pls feel free to contact Mr Chris
Tel: 0086-755-89948019
Fax: 0086-755-89948030
Mobile：0086-18938867508
E-mail: hyi(at)szrl(dot)net
|
|
| » Posted by: Shenzhen Hong Ye Jie Technology Co.,Ltd [China] |
|
|
|
|
|
[Sell]
pad printing silicoe rubber |
|
|
Applications of pad printing silicone rubber
Pad printing silicone rubber is mainly use for printing irregular patterns of plastic toys, electroplating toys, trade makers. The printing pad is a carrier which transfers the patterns on the steel plate onto the surface of the toys or products.
Features of pad printing silicone rubber
Pad printing silicone rubber has the advanced features of abrasion resistance, good printing effects and has no impurities. Meanwhile, pad printing silicone rubber is permanent and durable. Different colors are available if requested and we also provide free catalyst if you need it.
Operating instructions of pad printing silicone rubber
Pad printing silicone rubber is a kind of two-components silicone. Part A is the liquid silicone rubber, part B is the catalyst. Generally, the mxing ratio of silicone rubber and catalyst is 100 : 2 to 100:3 which means you can add 2-3 g catalyst if you take 100g liquid silicone rubber. Remember to mix them evenly and pour it on your mold. 2-4 hours later, you can obtain a printing pad.
Frequently asked question of pad printing silicone rubber:
The reasons why the silicone pad has a short service life are listed as follows:
(1)The problem caused by inappropriate filtration of silicone rubber, and impurities in the packaging process due to the uncleanness of barrels and bags.
(2)The short service life of the silicone pad has a close relationship with the adding amount of silicone oil. The more the silicone oil added, the softer the silicone pad will be. The silicone oil will destroy the molecule of the silicone rubber, thereby bringing about the non-durable and easy ageing of the silicone pad.
(3)All the users should know the properties of pad printing silicone rubber. The service life of the silicone pad has close relationship with the size of the printed patterns. For example, if a big pattern to be printed, a big silicone pad is required; if a small pattern to be printed, a small silicone pad (the silicone pad has to be adjusted according to the size of the patterns, and the proportion between the size of the silicone pad and the pattern is 3:1.)
Place of Origin: Guangdong China
Brand Name: HY silicone rubber
Model Number: HY9 series rubber for pad printing
Payment & Shipping Terms:
Minimum Order Quantity: 200 Kilogram
Packaging Details: 20kg/drum and 200kg/drum
Delivery Time: within 3 days after payment confirmed in our bank.
Payment Terms: L/C, T/T
Supply Ability: 8 Ton per Day
Any questions, please feel free to contact Cassi:
TEL: 0086-755-89948006
FAX: 0086-755-89948030
Mobile:0086-13427963991
Website: www(dot)szrl(dot)net
E-MAIL:hycassi(at)hotmail(dot)com
|
|
| » Posted by: Shenzhen Hong Ye Jie Technology Co., Ltd. [China] |
|
|
|
|
|
[Sell]
manual silicone rubber |
|
|
Applications of manual mold silicone rubber
Manual mold design silicone rubber is mainly applicable to manual mold design of manual mold, PVC plastic molds, cement product molds, low melting point alloy molds, alloy toy craftworks, plastic toys craftworks, gifts and stationery, duplication of large statues and cultural relics, shoe sole mold fabrication, pad printing allocation, antivibration of electronic equipments etc.
Features of manual mold silicone rubber
Manual mold silicon rubber has the features of good elasticity, non-deformation, high temperature resistance, good tensile strength and low shrinkage. The reproduction times are determined by the requirements of customers.
Operations of manual mold silicone rubber
Firstly, prepare the model mold or the product to be duplicated, take certain amount of silicon rubber, add 2-3% solid curing agent, and mix evenly. Then the mixed silicone rubber is ready for use. One mold can be solidified and formed in 2-3 hours.
(Note: our company does not recommend you to add silicon oil. If a special soft silicon mold or fine detailed and complex patterns products are required, 5%-10% silicon oil can be added to soften the mold for easy demolding.)
Place of Origin: Guangdong China
Brand Name: HY silicone rubber
Model Number: HY5 series rubber for manual mold making
Payment & Shipping Terms:
Minimum Order Quantity: 200 Kilogram
Packaging Details: 25kg/drum and 200kg/drum
Delivery Time: within 3 days after payment confirmed in our bank.
Payment Terms: L/C, T/T
Supply Ability: 5 Ton per Day
Any questions, please feel free to contact Cassi:
TEL: 0086-755-89948006
FAX: 0086-755-89948030
Mobile：0086-18938867521
Website: www(dot)szrl(dot)net
E-MAIL: hycassi(at)hotmail.com |
|
| » Posted by: Shenzhen Hong Ye Jie Technology Co., Ltd. [China] |
|
|
|
|
|
[Sell]
molding silicone rubber |
|
|
Applications of molding silicone rubber
Molding silicone rubber is primarily intended for the duplication and mold making of poly resin crafts, PU crafts, PU resin crafts, gypsum crafts, unsaturated resin crafts, lighting and candles crafts, plastic toy, stationery gifts industry, furniture decoration materials, Buddhist statue crafts, building decoration materials, large-scale cement mold, artificial fossils factory, Europe component factory, simulative landscapes, animals and plants sculpture, sandstone crafts and so on.
Features of molding silicone rubber
Molding silicone rubber is a kind of white or red flowing liquid with general hardness of 22-50A° after curing. Molding silicon rubber is elastic and high-temperature resistant and acid & alkali resistant. Molding silicone rubber also has the features of non-deformation, good tension and high tensile and tear strength.
Operations of molding silicone rubber
If the customer wants to make large products and large sized molds, the mold should be made of silicon rubber with high hardness. On the contrary, customers need to chose the silicone rubber with low hardness when making the molds with fine and precision patterns. The amount of the curing agent depends on the actual requirements of the customer. If molds requires fast drying and demold, more curing agent is needed. Contrarily, less curing agent is needed if molds requires slower drying and demold.
(Note: our company does not recommend you to add silicone oil. If a special soft silicone mold or fine detailed and complex patterns products are required, 5%-10% silicone oil can be added to soften the mold for easy demolding.)
Frequently asked questions of molding silicone rubber
Why does the silicone rubber mold have few molding times?
The silicone rubber mold has few molding times is due to follwoing reasons: adding too much silicone oil which will destroy the molecular of silicone rubber; making the mold for small and fine detailed products with higher hardness silicone rubber which is easy to break; making the mold for large products with soft silicone rubber which will reduce the tensile and tear strength of the mold, and the mold will have deformation. Thus, we should take the proper silicone rubber to make the mold for suitable products.
Place of Origin: Guangdong China
Brand Name: HY silicone rubber
Model Number: HY6, HY7 series rubber for mold making
Payment & Shipping Terms:
Minimum Order Quantity: 200 Kilogram within 3 days after payment confirmed in our bank.
Packaging Details: 25kg/drum and 200kg/drum
Delivery Time:
Payment Terms: L/C, T/T
Supply Ability: 8 Ton per Day
Any questions, please feel free to contact Cassi:
TEL: 0086-755-89948006
FAX: 0086-755-89948030
Mobile:0086-18938867521
Website: www(dot)szrl(dot)net
E-MAIL:hycassi(at)hotmail(dot)net |
|
| » Posted by: Shenzhen Hong Ye Jie Technology Co., Ltd. [China] |
|
|
|
|
|
[Sell]
liquid silicone rubber for gypsum products molding |
|
|
liquid silicone rubber for gypsum products molding
Application of liquid silicone rubber for gypsum products molding
Liquid silicone rubber for gypsum products molding is mainly applicable to gypsum products, plaster,resin, cements mold is good for casting Plasters, Cements and resin, toy craftworks, gifts and stationery, large statues, duplication of cultural relics mold making, etc.
Description of liquid silicone rubber for gypsum products molding
liquid silicone rubber for gypsum products molding is flowing liquid with consistant quality in whatever color. It consists of two components, wherein component A is silicone rubber, and component B is curing agent or vulcanizing agent. Firstly process and prepare the model mold or the product to be duplicated, take certain amount of the silicone rubber, add 2-3% curing agent, and mix evenly for use. One mold pair can be solidified and formed in 2-3 hours. The formed mold can be used repeatedly without deformation and water shrinkage and with high temperature resistance, thereby providing fast duplication of the product with a product shrinkage 2. The 618 manual mold silicon is mainly applicable to manual molds and small number of product duplication.
Operation Instruction of liquid silicone rubber for gypsum products molding
1. liquid silicone rubber for gypsum products molding is applied to small products or products with fine patterns. The mold for the fine detailed and small products should be made of soft silicon to protect the products from easy breaking when demoulding.
2. If large product duplication or fabrication, the mold should be made of higher hardness silicone rubber so that the products made will not deform.
Any questions,please feel free to contact Ms Cassi
TEL: 086-755-89948006
FAX: 086-755-89948030
MOBILE:086-18938867521
Website: www(dot)szrl(dot)net
E-MAIL: hyja(at)szrl(dot)net
|
|
| » Posted by: SHENZHEN HONG YE JIE TECHONOLOGY CO; LTD. [China] |
|
|
|
|
|
[Sell]
Equal to Dow Corning 3481( Silicone Rubber) |
|
|
Applications of Equal to Dow Corning 3481( Silicone Rubber)
Equal to Dow Corning 3481( Silicone Rubber) is primarily intended for poly resin crafts,PU crafts,PU resin crafts ,gypsum crafts ,unsaturated resin crafts, lighting and candles crafts ,plastic toy , stationery gifts crafts industry, a large statue Buddha, relievo furniture, furniture decorative materials, statues Buddha, artifacts copied, building decoration materials, large-scale cement mold, artificial fossils Factory,Europe component factory, simulation landscapes, animals and plants sculpture, sandstone crafts and so on.
Features of Equal to Dow Corning 3481( Silicone Rubber)
Equal to Dow Corning 3481( Silicone Rubber) is white or red flowing liquid with general hardness of 22-50shore A after curing. Molding silicone rubber is a kind elastic silicone rubber mold which features with resistance to deformation, high-temperature, acid-alkali and expansion as well as high reproduction times, good tensile strength ,tear strength and elongation.
Why does the silicone mold get burnt out?
The unsaturated resin produces great heat when added the curing agent. So you must demould the product within 3 minutes to avoid this problem.
Any questions,please feel free to contact Ms Cassi
TEL: 086-755-89948006
FAX: 086-755-89948030
MOBILE:086-18938867521
Website: www(dot)szrl(dot)net
E-MAIL: hyjg(at)szrl(dot)net
|
|
| » Posted by: SHENZHEN HONG YE JIE TECHONOLOGY CO; LTD. [China] |
|
|
|
|
|
[Sell]
Injection silicon rubber |
|
|
Injection silicon rubber applications
Injection silicon rubber is primarily intended for poly resin crafts, PU crafts, PU resin crafts ,gypsum crafts ,unsaturated resin crafts, lighting and candles crafts ,plastic toy , stationery gifts crafts industry, a large statue Buddha, furniture, furniture decorative materials, statues Buddha, artifacts copied, building decoration materials, large-scale cement mold, artificial fossils Factory, Europe component factory, simulation landscapes, animals and plants sculpture, sandstone crafts and so on.
Injection silicon rubber features description
Injection silicon rubber is white or red flowing liquid with general hardness of 22-50A°after curing. Molding silicon rubber is a kind elastic silicon rubber mold which features with resistance to deformation, high-temperature, acid-alkali and expansion as well as high reproduction times, good tensile strength, tear strength and elongation.
Injection silicon rubber operations
If the customer wants to make large products and large size molds, the mold should be made of silicon rubber with high hardness. On the contrary, if the mold with fine and precision patterns, it should be made of silicon with low hardness. The amount of the curing agent depends on the actual requirements of the customer. If molds requiring fast drying and demold, more curing agent is needed; contrarily, if molds requiring slower drying and demold, less curing agent is needed.
(Note: our company does not recommend you to add silicone oil. If a special soft silicone mold or fine detailed and complex patterns products are required, 5%-10% silicone oil can be added to soften the mold for easy demold.)
Frequently asked questions of injection silicon rubber
Why does the injection silicon rubber have few molding times?
The injection silicon rubber has few molding times is due to follwoing reasons: adding too much silicone oil which will destroy the molecular of silicone rubber; making the mold for small and fine detailed products with higher hardness silicone rubber which is easy to break; making the mold for large products with soft silicone rubber which will reduce the tensile and tear strength of the mold, and the mold will have deformation. Thus, we should take the proper silicone rubber to make the mold for suitable products.
Any questions,please feel free to contact Ms Cassi
TEL: 086-755-89948006
FAX: 086-755-89948030
MOBILE:086-18938867521
Website: www(dot)szrl(dot)net
E-MAIL: hyjg(at)szrl(dot)net
|
|
| » Posted by: SHENZHEN HONG YE JIE TECHONOLOGY CO; LTD. [China] |
|
|
|
|
|
[Sell]
Silicone Rubber Mouldings |
|
|
1.Application of Silicone Rubber Mouldings
Silicone Rubber Mouldings mainly used for shoe molds, sand casting, sole sampling, plaster models, simple products, products with non-complex patterns, as well as product models with stable size and non-deformation.
2.Operation instruction of Silicone Rubber Mouldings
Silicone Rubber Mouldings is composed of two components.Component A is white flowing liquid while component B is the curing agent.
Steps:
a.take silicone rubber of 100g and add 2% curing agent for mixing evenly.
b. After the silicone rubber and the curing agent are completely mixed, put the silicon into a vacuum machine for deairing to remove the bubbles.
c.After deaired, pouring the liquid silicone rubber into the product to be duplicated or into the mold frame.
Note: Silicone Rubber Mouldings is used for pouring or brushing technique. That is to say,
firstly fix the product or sole model to be duplicated onto a plane plate,
then enclose the plane frame with wooden plates to prevent the leakage of the silicon ,
thirdly mix the silicone rubber and the curing agent evenly according to the mixing ratio of 100 : 2 and pour them onto the sole model,
at last brush evenly with a wooden plate or a brush, and fill up the mold frame with gypsum after the silicone rubber is dried.
3.Storage and Precautions of Silicone Rubber Mouldings
Silicone Rubber Mouldings, which is an environmentally-friendly liquid silicone product, is not easy to burn and can be stored and transported as non-hazardous goods. The shelf life of the product is about one year from the date of production. Inspection is required when exceeding the time limited. It can continue to be used in case of neither thickening nor deterioration.
Any questions,please feel free to contact Ms Cassi
TEL: 086-755-89948006
FAX: 086-755-89948030
MOBILE:086-18938867521
Website: www(dot)szrl(dot)net
E-MAIL: hyjg(at)szrl(dot)net
|
|
| » Posted by: SHENZHEN HONG YE JIE TECHONOLOGY CO; LTD. [China] |
|
|
|
|
|
[Sell]
RTV-2( Liquid )silicone rubber for Candle crafts decorations |
|
|
RTV-2( Liquid )silicone rubber for Candle crafts decorations
RTV-2( Liquid )silicone rubber using area
1. RTV-2( Liquid )silicone rubber can used for poly resin crafts, PU crafts, PU resin crafts ,gypsum crafts ,unsaturated resin crafts, lighting and candles crafts ,plastic toy , stationery gifts crafts industry,
2. RTV-2( Liquid )silicone rubber is applicable for large statue Buddha, relievo furniture, furniture decorative materials, statues Buddha, artifacts copied, building decoration materials, large-scale cement mold,
3. RTV-2( Liquid )silicone rubber is intend for artificial fossils Factory, Europe component factory, simulation landscapes, animals and plants sculpture, sandstone crafts and so on.
RTV-2( Liquid )silicone rubber for Candle crafts decorations feature:
1.Two-part silicon rubber:flowable liquid silicon and curing agent.
2.Cures at room temperature within 6-8 hours.
3.An exceptional fluidity and good operability, easy to demold.
4.Good tensile and tear strength, low shrinkage.
5.High duplication times
why chose RTV-2( Liquid )silicone rubber for Candle crafts decorations
RTV-2( Liquid )silicone rubber is an effective and inexpensive way to create multiple copies of a master prototype part when you need a spec-like material for multiple sets, in a short timeframe, for less than a traditional tool would cost.
rtv-2 Silicone molds are capable of reproducing remarkable detail, and because of the flexibility of silicone, draft angles, inserts, and undercuts are not as critical as in other molding processes.
During operate the three impotant thing to pay attention :
1. weigh the liquid silicone rubber and curing agent exatly .
2. Stir the liquid silicone rubber and curing agent evenly .
3.we shouldchoose the right hardness to making diffirent size of product mold.
Certificate of RTV-2( Liquid )silicone rubber
Rohs
ISO2009
FDA
SGS
Any questions,please feel free to contact Ms Cassi
TEL: 086-755-89948006
FAX: 086-755-89948030
MOBILE:086-18938867521
Website: www(dot)szrl(dot)net
E-MAIL: hyjg(at)szrl(dot)net
|
|
| » Posted by: SHENZHEN HONG YE JIE TECHONOLOGY CO; LTD. [China] |
|
|
|
|
|
[Sell]
RTV Condensation Cure Silicone Rubber |
|
|
Applications of RTV Condensation Cure Silicone
RTV Condensation Cure Silicone is primarily intended for poly resin crafts,PU crafts,PU resin crafts ,gypsum crafts ,unsaturated resin crafts, lighting and candles crafts ,plastic toy , stationery gifts crafts industry, a large statue Buddha, relievo furniture, furniture decorative materials, statues Buddha, artifacts copied, building decoration materials, large-scale cement mold, artificial fossils Factory,Europe component factory, simulation landscapes, animals and plants sculpture, sandstone crafts and so on.
Features of RTV Condensation Cure Silicone
RTV Condensation Cure Silicone is white or red flowing liquid with general hardness of 22-50shore A after curing. Molding silicone rubber is a kind elastic silicone rubber mold which features with resistance to deformation, high-temperature, acid-alkali and expansion as well as high reproduction times, good tensile strength ,tear strength and elongation.
Any questions,please feel free to contact Ms Cassi
TEL: 086-755-89948006
FAX: 086-755-89948030
MOBILE:086-18938867521
Website: www(dot)szrl(dot)net
E-MAIL: hyjg(at)szrl(dot)net
|
|
| » Posted by: SHENZHEN HONG YE JIE TECHONOLOGY CO; LTD. [China] |
|
|
|
|
|
[Sell]
Silikon (Silicone rubber supplier) |
|
|
Silikon (Silicone rubber supplier) Main applications:
Silikon is mainly used for making molds for duplications for the industries such as Poly resin, epoxy poly-resin, plaster crafts, soap crafts, candles crafts, lighting, architectural decorations, embossed furnitures, plastic toys, gifts and stationeries, large statues.
Silikon (Silicone rubber supplier) Features:
Silikon are low viscosity, good fluidity, high tensile and tear strength, produced by molds can be used repeatedly, longer life expectancy.
Silikon (Silicone rubber supplier) Operations:
(1) Mixing:Silikon (Silicone rubber supplier) is a kind of flowing liquid and it contains two parts. Part A is a kind of white flowing liquid and part B is the curing agent. Remember to mix part A and part B completely, otherwise the silicon rubber will be partially solidified and this will give birth to difficulties in your final operation. What’s more, the finished moulds will meet a short life. All of these will cause a waste of silicon rubber.
(2) Vacuum pumping: After finishing the first step, then go to the vacuum pumping . Usually, there will be some air bubbles in the mixture during the mixing process working. So after the first step after finishing handling of the original mold, we need come to the vacuum pumping process.This step is better for taking less than 3-5 minutes. Otherwise, it will cause cross linking reaction, and no more further steps will be available.
Any questions,please feel free to contact Ms Cassi
TEL: 086-755-89948006
FAX: 086-755-89948030
MOBILE:086-18938867521
Website: www(dot)szrl(dot)net
E-MAIL: hyjg(at)szrl(dot)net
|
|
| » Posted by: SHENZHEN HONG YE JIE TECHONOLOGY CO; LTD. [China] |
|
|
|
|
|
[Sell]
Silicone Rubber Mold Material/Silicone Moulds Material |
|
|
Silicone Rubber Mold Material/Silicone Moulds Material Description
Silicone Rubber Mold Material/Silicone Moulds Material is primarily intended for poly resin crafts,PU crafts,PU resin crafts ,gypsum crafts ,unsaturated resin crafts, lighting and candles crafts ,plastic toy , stationery gifts crafts industry, a large statue Buddha, relievo furniture, furniture decorative materials, statues Buddha, artifacts copied, building decoration materials, large-scale cement mold, artificial fossils Factory,simulation landscapes, animals and plants sculpture, sandstone crafts and so on.
Silicone Rubber Mold Material/Silicone Moulds Material for Features
Silicone Rubber Mold Material/Silicone Moulds Material is white or red flowing liquid with general hardness of 22-50A°after curing. Molding silicon rubber is a kind elastic silicon rubber mold which features with resistance to deformation, high-temperature, acid-alkali and expansion as well as high reproduction times, good tensile strength ,tear strength and elongation.
Silicone Rubber Mold Material/Silicone Moulds Material for operations
Silicone Rubber Mold Material/Silicone Moulds Material If the customer wants to make large products and large size molds, the mold should be made of silicon rubber with high hardness. On the contrary, if the mold with fine and precision patterns, it should be made of silicon with low hardness. The amount of the curing agent depends on the actual requirements of the customer. If molds requiring fast drying and demould, more curing agent is needed; contrarily, if molds requiring slower drying and demould, less curing agent is needed.
(Note: our company does not recommend you to add silicone oil. If a special soft silicon mold or fine detailed and complex patterns products are required, 5%-10% silicone oil can be added to soften the mold for easy demould.)
Any questions,please feel free to contact Ms Cassi
TEL: 086-755-89948006
FAX: 086-755-89948030
MOBILE:086-18938867521
Website: www(dot)szrl(dot)net
E-MAIL: hyjg(at)szrl(dot)net
|
|
| » Posted by: SHENZHEN HONG YE JIE TECHONOLOGY CO; LTD. [China] |
|
|
|
|
|
[Sell]
Mould Making Silicone Rubber |
|
|
1.Applications of mould making silicone rubber
Mould making silicon rubber is suitable for industries such as toys, gifts, decoration, plate engrave, human replica, art crafts, resin crafts, poly resin crafts, unsaturated resin crafts, candle crafts, plastic crafts, stationeries, plaster crafts and Buddhist statue crafts.
2.Features of mould making silicone rubber
a. Good characteristics of easy-operation
b. Light viscosity and good flowability
c. Low shrinkage
d. Favorable tension
e. No deformation
f. Favorable hardness
g. High temperature resistance, acid and alkali-resistance and ageing resistance
3.Two series of mould making silicone rubber are divided, HY-6 and HY-7
HY-6 Series includes model codes of HY-620, HY-640, HY-628, HY-638
HY-7 Series includes model codes of HY-718, HY-728, HY-738
4.FAQ of mould making silicone rubber
Why could the silicon mold be reused only for a few times?
It can be due to the following reasons:
a. Adding too much silicone oil in to silicon rubber. Silicone oil is an additive which destroies the molecular weight of silicone rubber and reduce the tension and tear strength.
b. Using the silicon rubber with a high hardness to make molds for small sized products with delicate and intricate designs and the silicon rubber with a low hardness to makes molds for large sized products with simple designs.
Notes: we should choose the silicon rubber specifically according to the requirements of our products to avoid this problem.
5. Other details
Place of Origin Guangdong China
Brand Name Hong Ye Silicone Rubber
Model Number HY625 HY630 silicone rubber
Payment & Shipping Terms:
Minimum Order Quantity: 200 Kilogram
Price: FOB shenzhen USD 5.2-7.4/kg
Packaging Details: 25kg/drum and 200kg/drum
Delivery Time: within 3 days after payment confirmed in our bank.
Payment Terms: L/C at sight, T/T
Supply Ability: 8 Ton per Day
Certifications:RoHS.MSDS.SGS ISO9001:2000
Any questions of mould making silicone rubber, please feel free to contact Taylor :
Mob: +86-18938867522
Tel: + 86-755-89948006
E-mail: hyw(at)szrl(dot)net
Skype: taylordl828
Facebook: hyw(at)szrl(dot)net |
|
| » Posted by: SHENZHEN HONG YE JIE TECHONOLOGY CO; LTD. [China] |
|
|
|
|
|
[Sell]
Manual Molding Silicone Rubber |
|
|
1. Applications of Manual Molding Silicone Rubber
Manual molding silicone rubber is mainly used for model design of manual mold, PVC plastic molds, cement products, low melting point alloy molds, alloy toys, plastic toys, electronics, handicrafts, stationery, large-scale sculpture, reproduction of cultural relic, shoe sole molds, pad printing allocation, Electronic equipment antivibration, etc.
2．Model Codes of Manual Molding Silicone Rubber
HY-528# is applicable to make molds of smaller products and the production will be 2-3 pieces.
HY-540#, compared to other two types, for its moderate hardness and better quality & performance, its production will be 20-30 pieces.
HY-570# is applicable to large size products duplications and Electronic equipment antivibration.
3．Features of Manual Molding Silicone Rubber
a. good elasticity
b. non-deformation
c. high temperature resistance
d. low shrinkage.
4. Operation Instructions for Manual Molding Silicone Rubber
Manual molding silicone rubber is a flowable liquid, and the quality has nothing to do with the color. It consists of two component. Part A is a flowable liquid silicone rubber, part B is the curing agent. Firstly, after your previous work of dealing with the original model, take some liquid silicone rubber, add 2%-3% curing agent of the amount of silicon, and mix them evenly. Then after vacuum-pumping the mixture, you can pour it into the mold frame. The silicone mold will cured in 2-3 hours.
Note: The time for vacuum-pumping should be less than 3—5 mins ,otherwise, once the silicone rubber has cross-link reaction during vacuumizing, it will not be operated.
5. FAQ of Manual Molding Silicone Rubber
How to prevent silicone manual molds getting sticky?
The main reason for this problem is that you do not handle the products or original molds well, then you should deal with the original mold or products carefully before molding. Such as for the products with a complicated pattern or a unsmoothed surface, you should polish and clean the products after which it will be molded ,then spray the release agent. Normally, the release agent can be Vaseline , detergent. liquid wax Etc. In practical process, you can bush different release agent according to different material.
The second reason is that the operator pour the silicone into the mold when the mixture is mixed evenly, then the finish silicone mold will not cure and dry entirely.
6. Other details
Place of Origin Guangdong China
Brand Name Hong Ye Silicone Rubber
Model Number HY528, HY540 manual mold silicone rubber
Payment & Shipping Terms:
Minimum Order Quantity: 200 Kilogram
Price: FOB shenzhen USD 4.8-7.5/KG
Packaging Details: 25kg/drum and 200kg/drum
Delivery Time: within 3 days after payment confirmed in our bank.
Payment Terms: L/C at sight,T/T
Supply Ability: 8 Ton per Day
Certifications:RoHS.MSDS.SGS ISO9001:2000
Further information on manual molding silicone rubber, Please feel free to contact Taylor：
Mob: +86-18938867522
Tel: + 86-755-89948006
E-mail: hyw(at)szrl(dot)net
Skype: taylordl828
Facebook: hyw(at)szrl(dot)net |
|
| » Posted by: SHENZHEN HONG YE JIE TECHONOLOGY CO; LTD. [China] |
|
|
|
|
|
«back
Pages: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 next»
|
|
|
