|
|
|
|
|
|
|
[Sell]
Universal Rubber Machinery |
 |
|
| Universal Rubber Machinery, Internal (Banbury) Mixer is the best machine for mixing of big quantity plastic and rubber material. This Banbury Mixer is mainly used for plasticizing and mixing of natural rubber, synthetic rubber, reclaimed rubber and plastics, foaming plastics, and used in mixing of various the degree materials. Technical Advantages: 1. The diversity of rotor type can meet different mixing requirements. User can choose any kind of rotors (the mixer with different rotor has different total volume and working volume. 2. Drive system adopts DC motor or AC inverter motor to realize stepless speed adjustment or adopts Ac Motor with gear box etc. The drive system has the advantages of steady drive, lower noise and long service life etc. 3. The standard rotor adopts the right drive system. According to users needs we also can supply the left drive system. 4. Drive system adopts DC motor or AC inverter motor to realize stepless speed adjustment or adopts Ac motor with gear box etc. The drive system has the advantages of steady drive, lower noise and long service life etc. 5. On-site operation cabinets and electrical control cabinets adopt PLC communication, results in reduction of equipment troubles and installation cost. Construction Features: 1. With completely condition, materials are mixed or plasticizing under certain pressure, controllable temperature, which makes high production efficiency and obtains excellent quality 2. Spiral angle and over lapping length of blades of the rotors are of reasonable design and make the materials to be dispersed uniformly 3. Surface where is contacted with the materials are all plated with hard chromium and polished, which is corrosion-resistant and wear-resistant 4. Jacket construction is adopted in parts that surfaces contact with materials to achieve excellent water-cooling or steam heating effect and fit in with the needs of plastics and rubber processing technology. |
|
» Posted by: Qingdao Shun Cheong Machinery Co., Ltd [China]  |
|
|
|
|
|
[Sell]
RTV Silicone rubber HY-638 for concrete casting |
|
|
Usage:
RTV Silicone rubber HY638 is most suitable for concrete castings, cement statue, concrete pavers, GRC cement products, etc. with the advantages of good tensile strength, high tear strength, high temperature resistance, high duplication times and repeated use, etc.
It is suitable for large products with detailed pattern, which is difficult to demould.
This silicone rubber is one of the products with the highest use level in the production of concrete castings and the shrinkage is up to 0.2%.
Description: 　　
RTV-2 molding silicon rubber and silicone rubber are general called two-component room temperature vulcanization silicone rubber with excellent fluidity and good operational performance.
Add curing agent of 2%~5% at the room temperature, the silicone rubber is still operational within 30 minutes, and in 2-3 hours, an elastic silicon mold will be obtained with resistance to deformation, high-temperature, acid and alkali and expansion.
Standard datasheet:
Model appearance viscosity (cps): 20000~26000
Hardness (shore A): 32~36
Tensile Strength (Kgf/cm2):45~51
Tear strength (Kgf/㎝): 20~25
Elongation (%) ≧500
Mixing ratio (%):2~3
Operating time (h): 0.5
Curing time (h):2~4
Operation instruction for RTV-2 silicone rubber HY638#:　　
The product is white or red flowing liquid with general hardness of 22~50 shore A after curing.
If the customer wants to make large products and large size molds, the mold should be made of silicone rubber with high hardness.
On the contrary, if the mold with fine and precision patterns, it should be made of silicon with low hardness.
The amount of the curing agent depends on the actual requirements of the customer.
If molds requiring fast drying and demould, more curing agent is needed; contrarily, if molds requiring slower drying and demould, less curing agent is needed.
Notes:
We do not recommend adding silicone oil. If a special soft silicon mold or fine detailed and complex patterns products are required, 5%~10% silicone oil can be added to soften the mold for easy demould.
The proportions and reactions of the curing agent and the silicon are listed as follows: 　　
Adding curing agent 1%, the silicone can still be operated within 2.5 hours and can be demoulded after 6-8 hours. 　　
Adding curing agent 2%, the silicone can still be operated within 50 minutes to 1 hour and can be demoulded after 2-3 hours. 　　
Adding curing agent 3%, the silicone can still be operated within 28 - 30 minutes and can be demoulded after 1.5-2 hours.
Adding curing agent 4%, the silicone can still be operated within 10 - 15 minutes and can be demoulded.
Any further information pls feel free to contact with Ms Nina
Shenzhen Hong Ye Jie Technology Co., Ltd.
|
|
| » Posted by: Shenzhen Hong Ye Jie Tech Co., Ltd. [China] |
|
|
|
|
|
[Sell]
Addition cure silicone rubber for making molds |
|
|
1. Brief description of Addition cure silicone rubber :
Addition cure silicone rubber is mainly used for metallic arts & crafts, baby nipples, cake, candy food grade products mold making, medical catheter and so on. It is nontoxic and with very low shrinkage.
2. Addition cure silicone rubber applications:
Addition cure silicone rubber is mainly used for metallic arts & crafts, baby nipples, cake, candy food grade products mold making, life casting, medical catheter and so on.
3. Addition cure silicone rubber features:
a) Two-component silicone rubber with platinum catalyst
b) With high transparency, tensile strength, and tear strength.
c) Nontoxic & reach to Food grade
d) With good heat stability and weatherability ( temperature resistant range of -60—250 C)
e) With heat-ageing resistance
Any further information pls feel free to contact with Ms Nina
TEL: 0086-755-89948019
Fax: 0086-755-89948030
E-mail: hyjr(at)szrl(dot)net
Website: www(dot)szrl(dot)net
Place of Origin: Guangdong China
Brand Name: Hong Ye Silicone Rubber
Model Number: HY-E620, HY-E630, HY-E642 addition cure silicone rubber
Minimum Order Quantity: 100 Kilogram
Price: FOB shenzhen 9.35~14 USD /KG
Packaging Details: 25kg/drum and 200kg/drum
Delivery Time: within 3 days after payment confirmed in our bank.
Payment Terms: L/C,T/T
Supply Ability: 8 Ton per Day
Certifications: RoHS/MSDS/SGS/ISO9001:2008
|
|
| » Posted by: Shenzhen Hong Ye Jie Tech Co., Ltd. [China] |
|
|
|
|
|
[Sell]
Manual mold silicon rubber HY540 |
|
|
Manual mold silicon rubber HY540 Description:
Manual mold silicon rubber HY540 is flowing liquid with consistant quality in whatever color. It consists of two components, A is silicone rubber, and B is curing agent or vulcanizing agent. Manual mold silicon rubber HY540 is mainly applicable to manual mold design, PVC plastic molds, cement product molds, melting point alloy molds, alloy toy craftworks, plastic toy craftworks, gifts and stationery, large statues, cultural relics duplication, shoe sole mold fabrication, pad printing positioning, electronic equipments antivibration, etc.
Manual mold silicon rubber HY540 Standard Datasheet:
Appearance White
Viscosity(cps) ≤18000
Hardness(Ao) 38±2
TensileStrength (Mpa) ≥2.0
Tear Strength (KN/m) ≥7
Elongation(%) ≥200
Mixing Ratio (%) 2~3
Pot life (H) 0.5
Demould time(H) 2~4
Manual Mold Silicon Rubber FAQ:
How to prevent silicon manual molds getting sticky?
The main reason for this problem is that you do not handle the products or original molds well, then you should deal with the original mold or products carefully before molding. Such as for the products with a complicated pattern or a unsmoothed surface, you should polish and clean the products after which it will be molded , then spray the release agent. Normally, the release agent can be Vaseline , detergent. liquid wax Etc. In practical process, you can bush different release agent according to different material.
The second reason is that the operator pour the silicon into the mold when the mixture is mixed evenly, then the finish silicon mold will not cure and dry entirely.
Any further information pls feel free to contact with Ms Nina
TEL: 0086-755-89948019
Fax: 0086-755-89948030
E-mail: hyjr(at)szrl(dot)net
Website: www(dot)szrl(dot)net
|
|
| » Posted by: Shenzhen Hong Ye Jie Tech Co., Ltd. [China] |
|
|
|
|
|
[Sell]
molding silicone rubber HY620 |
|
|
Molding Silicone Rubber HY620 Description:
Molding Silicone Rubber HY620 is mainly used for toy gifts and craftwork gifts with the advantages of good tensile strength, high tear strength, high temperature resistance, high duplication times and repeated use, etc. It is suitable for small products or fine and precision products which is difficult to demould. This molding Silicone Rubber is one of the products with the highest use level in the production of craftwork gifts and the shrinkage is up to 2‰.
Molding Silicone Rubber Standard Datasheet:
Model 620
Appearance White
Viscosity (cps) ≤16000
Hardness (A°) 20±2
Tensile strength (Mpa) ≥2.8
Tear strength (KN/m) ≥20
Elongation (%) ≥400
Mixing ratio (%) 2~3
Operating time(H) 0.5~1
Curing time(H) 2~5
Molding silicone rubber Operation Instruction:
Molding silicone rubber is white or red flowing liquid with general hardness of 18-22A°after curing . If the customer wants to make large products and large size molds, the mold should be made of silica gel with high hardness. On the contrary, if the mold with fine and precision patterns , it should be made of liquid silicone with low hardness. The amount of the curing agent depends on the actual requirements of the customer. If molds requiring fast drying and demould, more curing agent is needed; contrarily, if molds requiring slower drying and demould, less curing agent is needed.
(Note: our company does not recommend you to add silicone oil. If a special soft liquid silicone mold or fine detailed and complex patterns products are required, 5%-10% silica gel oil can be added to soften the mold for easy demould.)
Molding Silicone Rubber FAQ:
Why is the appearance of the finished mold striate and unsmooth?
It is because the appearance of the product or the model itself is not perfect, and it has not been polished before the further operation. So when you make silicon molds, firstly you should polish the products, spray the realese agent evenly on the product. In this case, the problem can be avoided.
Any further information pls feel free to contact with Ms Nina
TEL: 0086-755-89948019
Fax: 0086-755-89948030
E-mail: hyjr(at)szrl(dot)net
Website: www(dot)szrl(dot)net
|
|
| » Posted by: Shenzhen Hong Ye Jie Tech Co., Ltd. [China] |
|
|
|
|
|
[Sell]
Liquid silicone for gypsum column mold making |
|
|
Liquid silicone for gypsum column mold making applications;
Liquid Silicone for gypsum column mold making is primarily intended for poly resin crafts, PU crafts, PU resin crafts, gypsum crafts, gypsum column, unsaturated resin crafts, lighting and candles crafts, plastic toy, stationery gifts crafts industry, a large statue Buddha, relievo furniture, furniture decorative materials, statues Buddha, artifacts copied, building decoration materials, large-scale cement mold, artificial fossils Factory, Europe component factory, simulation landscapes, animals and plants sculpture, sandstone crafts and so on.
Liquid silicone for gypsum colum mold making features:
Liquid Silicone for gypsum column mold making is white or red flowing liquid with general hardness of 22-50A° After curing. Molding silicon rubber is a kind elastic silicon rubber mold which features with resistance to deformation, high-temperature, acid-alkali and expansion as well as high reproduction times, good tensile strength, tear strength and elongation.
Liquid silicone for gypsum colum mold making operations:
If the customer wants to make large products and large size molds, the mold should be made of silicon rubber with high hardness. On the contrary, if the mold with fine and precision patterns, it should be made of silicon with low hardness. The amount of the curing agent depends on the actual requirements of the customer. If molds requiring fast drying and demold, more curing agent is needed; Contrarily, if molds requiring slower drying and demold, less curing agent is needed.
(Note: Our company does not recommend you to add silicone oil. If a special soft silicone mold or fine detailed and complex patterns products are required, 5%-10% silicone oil can be added to soften the mold for easy demould. )
Any further information pls feel free to contact with Ms Nina
TEL: 0086-755-89948019
Fax: 0086-755-89948030
E-mail: hyjr(at)szrl(dot)net
Website: www(dot)szrl(dot)net
|
|
| » Posted by: Shenzhen Hong Ye Jie Tech Co., Ltd. [China] |
|
|
|
|
|
[Sell]
Pad printing silicone rubber HY901 |
|
|
Pad printing silicone rubber HY901 Description:
The product with the advantages of abrasion resistance, high temperature resistance, good printing effect, etc. , which made of top-quality raw material due to adding American Dupont Teflon high-temperature resistance new material, is processed through high-temperature machining. The product is mainly applicable to plastics toys, electroplating products, electronic toys, trademarks and irregular pattern printing. The silicon pad is a carrier which transfer printing the patterns on the steel plate onto the toy products' surface.
Pad printing silicone rubber HY901 Usage:
Making the printing pads for plastic toys, craftworks, product printing.
Pad printing silicone rubber HY901 Standard Datasheet:
Model 901
Appearance Red /yellow /green /whitE
Viscosity (cps) ≤33000
Hardness (Ao) 28±2
Tensile strength (Mpa) ≥3.0
Tear strength (KN/m) ≥20
Elongation (%) ≥360
Mixing ratio (%) 2~3
Pot life (H) 0.5
Demould time(H) 2~4
Pad Printing Silicon Rubber FAQ
Why we should add silicon oil into pad printing silicon rubber?
Customers should change the hardness of the silicon pad according to the different patterns. Silicon oil can change the hardness and the viscosity of the liquid silicone rubber.
Any further information pls feel free to contact with Ms Nina
TEL: 0086-755-89948019
Fax: 0086-755-89948030
E-mail: hyjr(at)szrl(dot)net
Website: www(dot)szrl(dot)net
|
|
| » Posted by: Shenzhen Hong Ye Jie Tech Co., Ltd. [China] |
|
|
|
|
|
[Sell]
Electronic silicone rubber for LED encapsulation |
|
|
1.Features:
HY-9055# is a kind of low viscosity, Inherent flame resistance, two components addtion cured potting silicone with heat-conducting. It cures with both on room temperature and heated temperature. It has the feature of the higher temperature the faster of the curing time. It can be applied to electronic components for insulation, waterproofing, fixed and flame retardant. The flame retardant UL94-V0 level can be achieved. It mainly applied in electronic components surface with materials of PC(Poly-carbonate),PP,ABS,PVC, etc. and metal materials.
2.Application:
- high powered electronics,
- DC/DC module and circuit board which requires heat dissipation and high temperature resistance.
It can be broadly used for LED screen, Wind Power Generator, PCB substrate, etc.
3.TECHNICAL GUIDELINES:
a Pls put part A and part B in separate container and stir evenly before mixing the two part together.
b Weight Ratio: part A: part B = 1:1
c Degeneration the mixture in vacuum pump under 0.08 MPa for 3-5 minutes.
d The temperature influences the curing time of HY-9055#. When in too low temperature, we suggest customers appropriately heat the mixture to accelerate vulcanization. Suggested operation time and temperature. With temperature of 80~100°C, the silicone will cure in 15 minutes, while in 25°C room temperature, the silicone will cure around 8 hours.
4.Warm Tips:
a.Following material may hinder the curing of the product, So pls apply after summary experiment. When necessary, pls clean the application areas.
Condensation silicone which not completely cured or organic tin compounds.
Sulphur, sulfide and sulfur rubber materials.
Amine compounds as well as contains the amine materials.
Pewters solder flux.
b. Should be sealed storage.The mixture should be used up at once, avoid causing waste.
c. Silicone belongs to non-dangerous goods, but keep away from mouth and eyes.
d. When gets stratified after a period of storage, Please mix 9055 evenly before using, it does not affect the performance
Any further information pls feel free to contact with Ms Nina
TEL: 0086-755-89948019
Fax: 0086-755-89948030
E-mail: hyjr(at)szrl(dot)net
Website: www(dot)szrl(dot)net
|
|
| » Posted by: Shenzhen Hong Ye Jie Tech Co., Ltd. [China] |
|
|
|
|
|
[Sell]
XK-660 Rubber Mixing Mill |
|
|
| Rubber Mixing Mill is traditional equipment; we have been committed to developing new structure of the machine for many years. Through technological improvement and application, we have obtained the breakthrough improvement in many aspects, such as motive force transmitting system, safety factor and so on. Lower cost, higher efficiency and more humanization of operating have always been our pursuit. 1. This mixing mill can be equipped with hydraulic or mechanical device which can automatically make the rubber material be mixed over and over again. So the labor intensity and mixing time can be reduced greatly. 2. The Rubber mixing mill speed reducer is Hardened speed reducer, it is low noise, high efficiency, good transfer effect. 3. To ensure the safety of staff and equipment, we install convenient button for emergency. 4. All the mixing mills we provide to you are checked after 3-7 hours non-stop full load operation, perfect quality and low noise. Customers can use them immediately after installation. |
|
| » Posted by: Qingdao Shun Cheong Machinery Co., Ltd [China] |
|
|
|
|
|
[Sell]
Rubber Extruder |
|
|
| Hot Feed Rubber Extruder Used For the rubber tube, rubber, rubber sheet extrusion. Qingdao Shun Cheong Machinery Co., Ltd is an enterprise of technology-pioneer type specializing in production of rubber machinery and the leading manufacturer and export base of rubber machinery industry in China. Our rubber machinery includes: Rubber Bale Cutter, Internal Mixer, Banbury Intensive Kneader, banbury mixer, dispersion kneader, Butyl reclaimed rubber desulfurizing kneader, Two roll rubber mixing mill, open type rubber mixing mill, rubber cracker mill, rubber refiner, batch-off machine, rubber extruder, hot feeding rubber extruder, rubber calender, three roller Calender, Four roller Calender, plate vulcanizing press, tyre machine, tyre curing press, inner tube press, EVA foam press, hydraulic press, Conveyor belt vulcanizing press, conveyor belt vulcanizer, conveyor belt vulcanizing line, reclaimed rubber machinery, rubber powder machinery, rubber cracker and other rubber machinery. Meantime, we can design and produce conveyor belt, tyre, reclaimed rubber line according to customer's request. These products are well sold to more than 30 provinces, cities, and autonomous regions in China as well as 30 countries and regions in Southeast Asia, Middle-east, Africa, Middle-south America, Australia, Europe, and USA, etc. |
|
| » Posted by: Qingdao Shun Cheong Machinery Co., Ltd [China] |
|
|
|
|
|
[Sell]
X(S)N-75L Rubber Mixer |
|
|
| Rubber Mixer, Internal (Banbury) Mixer is the best machine for mixing of big quantity plastic and rubber material. This Banbury Mixer is mainly used for plasticizing and mixing of natural rubber, synthetic rubber, reclaimed rubber and plastics, foaming plastics, and used in mixing of various the degree materials. Technical Advantages: 1. The diversity of rotor type can meet different mixing requirements. User can choose any kind of rotors (the mixer with different rotor has different total volume and working volume. 2. Drive system adopts DC motor or AC inverter motor to realize stepless speed adjustment or adopts Ac Motor with gear box etc. The drive system has the advantages of steady drive, lower noise and long service life etc. 3. The standard rotor adopts the right drive system. According to users needs we also can supply the left drive system. 4. Drive system adopts DC motor or AC inverter motor to realize stepless speed adjustment or adopts Ac motor with gear box etc. The drive system has the advantages of steady drive, lower noise and long service life etc. 5. On-site operation cabinets and electrical control cabinets adopt PLC communication, results in reduction of equipment troubles and installation cost. Construction Features: 1. With completely condition, materials are mixed or plasticizing under certain pressure, controllable temperature, which makes high production efficiency and obtains excellent quality 2. Spiral angle and over lapping length of blades of the rotors are of reasonable design and make the materials to be dispersed uniformly 3. Surface where is contacted with the materials are all plated with hard chromium and polished, which is corrosion-resistant and wear-resistant 4. Jacket construction is adopted in parts that surfaces contact with materials to achieve excellent water-cooling or steam heating effect and fit in with the needs of plastics and rubber processing technology. |
|
| » Posted by: Qingdao Shun Cheong Machinery Co., Ltd [China] |
|
|
|
|
|
[Sell]
Lab Dispersion kneader |
|
|
| Lab Dispersion kneader, Banbury Intensive Kneader (dispersion kneader): Used rubber and plastic mixing, Excellent mixing, Volume: 3L, well sealed, no leakage of material. can be applied in the separate or mixing refining of raw glue, mix glue, rubber, plastic and other raw materials to manufacture various rubber products such as EVA frothing soles, rubber soles, TPR soles, rubber roller wheels, sponge, tyres, balls, rubber belts, capsules, grease seals, shockproof rubber, adhesive tapes, electric products and rubber products for vehicle. Technical Advantages: 1. The diversity of rotor type can meet different mixing requirements. User can choose any kind of rotors (the mixer with different rotor has different total volume and working volume. 2. Drive system adopts DC motor or AC inverter motor to realize stepless speed adjustment or adopts Ac Motor with gear box etc. The drive system has the advantages of steady drive, lower noise and long service life etc. 3. The standard rotor adopts the right drive system. According to users needs we also can supply the left drive system. 4. Drive system adopts DC motor or AC inverter motor to realize stepless speed adjustment or adopts Ac motor with gear box etc. The drive system has the advantages of steady drive, lower noise and long service life etc. 5. On-site operation cabinets and electrical control cabinets adopt PLC communication, results in reduction of equipment troubles and installation cost. Construction Character: 1. This rubber kneader has advanced and reasonable design, compact structure, covers little space area, easy installation, and high production efficiency, easy and reliable operation. 2. The mixing rubber room uses "w" type. Wall and rotor choose wear-resisting alloy steel integral mould, key parts first possessing by imported wear surfacing welding rod processed then by hard chromium plating, more tighten and durable. Mixing rubber room is easy to clean and replace pigment frequently. Good cooling and heating effect, mixed rubber spread evenly. New sealing design, good sealing affect, long life, safe and greatly improve the working environment. 3. Sidewall leak-proof device adopts high-tech materials-epoxy glass cloth made of high- pressure die- casting, its characteristic is not easy to wear and maintenance, no chemical reaction, between leak-proof seal and wear-resisting ring filling port, so can extend seal rings and increased life. 4. The rubber kneader pressure cover use "M" type structure, so the rubber mixed more evenly and thoroughly. |
|
| » Posted by: Qingdao Shun Cheong Machinery Co., Ltd [China] |
|
|
|
|
|
[Sell]
Hydraulic Vulcanizing machine |
|
|
| Hydraulic Vulcanizing machine Use for all kinds of vulcanizing mould, rubber and plastic mould products, and non-mould products. To our clients, there is a wide range of hydraulic pressed components at competitive prices. These components are made using excellent quality raw material to ensure dimensional stability. With the help of our adept professionals, we can even customize these components as per the specific requirements of the clients. The components offered by us find extensively application in the following industries: 1. Rubber Industries 2. Bakelite Mould 3. General engineering industry |
|
| » Posted by: Qingdao Shun Cheong Machinery Co., Ltd [China] |
|
|
|
|
|
[Sell]
XK-560 Rubber Mixing Machine |
|
|
| This rubber mixing machine ensures the perfect and uniform blending of natural and synthetic rubber with other raw materials. The machine mixes all the raw materials to the desired specifications. Advantageous Features: 1. This rubber mixing machine can be equipped with hydraulic or mechanical device which can automatically make the rubber material be mixed over and over again. So the labor intensity and mixing time can be reduced greatly. 2. The mixing machine speed reducer is planetary speed reducer, it is low noise, high efficiency, good transfer effect, 3. To ensure the safety of staff and equipment, we install convenient button for emergency. 4. All the rubber mixing machine we provide to you are checked after 3-7 hours non-stop full load operation, perfect quality and low noise. Customers can use them immediately after installation. |
|
| » Posted by: Qingdao Shun Cheong Machinery Co., Ltd [China] |
|
|
|
|
|
[Sell]
XK-400 Rubber Mixing Mill Manufacturer |
|
|
| Rubber machinery Manufacturer From China Qingdao Shun Cheong Machinery Co., Ltd. Our rubber machinery includes: Rubber Bale Cutter, Internal Mixer, Banbury Intensive Kneader, banbury mixer, dispersion kneader, Butyl reclaimed rubber desulfurizing kneader, Two roll rubber mixing mill, open type rubber mixing mill, rubber cracker mill, rubber refiner, batch-off machine, rubber extruder, hot feeding rubber extruder, rubber calender, three roller Calender, Four roller Calender, plate vulcanizing press, tyre machine, tyre curing press, inner tube press, EVA foam press, hydraulic press, Conveyor belt vulcanizing press, conveyor belt vulcanizer, conveyor belt vulcanizing line, reclaimed rubber machinery, rubber powder machinery, rubber cracker and other rubber machinery. Meantime, we can design and produce conveyor belt, tyre, reclaimed rubber line according to customer's request. |
|
| » Posted by: Qingdao Shun Cheong Machinery Co., Ltd [China] |
|
|
|
|
|
[Sell]
Rubber Refining Mill |
|
|
| Rubber Refining Mill,Rubber Refiner is mainly used for removing impurity substance of reclaimed rubber. Introduction: 1. It is mainly used for removing impurity substance of reclaimed rubber. 2. According the requirement of our customers and our experience for these years, we design and manufacture different kinds of rubber refining machines which are used for producing various strength reclaimed rubber. 3. Waist-dum type rolls, the rolling bearings are lubricated by lubricating grease. |
|
| » Posted by: Qingdao Shun Cheong Machinery Co., Ltd [China] |
|
|
|
|
|
[Sell]
XKJ-480 Rubber Refining Mill |
|
|
| XKJ-480 Rubber Refining Mill,Rubber Refiner is mainly used for removing impurity substance of reclaimed rubber. Introduction: 1. It is mainly used for removing impurity substance of reclaimed rubber. 2. According the requirement of our customers and our experience for these years, we design and manufacture different kinds of rubber refining machines which are used for producing various strength reclaimed rubber. 3. Waist-dum type rolls, the rolling bearings are lubricated by lubricating grease. |
|
| » Posted by: Qingdao Shun Cheong Machinery Co., Ltd [China] |
|
|
|
|
|
[Sell]
Frame Type Vulcanizing Press |
|
|
| Frame Type Vulcanizing Press Use for all kinds of vulcanizing mould, rubber and plastic mould products, and non-mould products. To our clients, there is a wide range of hydraulic pressed components at competitive prices. These components are made using excellent quality raw material to ensure dimensional stability. With the help of our adept professionals, we can even customize these components as per the specific requirements of the clients. The components offered by us find extensively application in the following industries: 1. Rubber Industries 2. Bakelite Mould 3. General engineering industry |
|
| » Posted by: Qingdao Shun Cheong Machinery Co., Ltd [China] |
|
|
|
|
|
[Sell]
Heavy Duty Hydraulic Machine |
|
|
| Hydraulic Machine Use for all kinds of vulcanizing mould, rubber and plastic mould products, and non-mould products. To our clients, there is a wide range of hydraulic pressed components at competitive prices. These components are made using excellent quality raw material to ensure dimensional stability. With the help of our adept professionals, we can even customize these components as per the specific requirements of the clients. The components offered by us find extensively application in the following industries: 1. Rubber Industries 2. Bakelite Mould 3. General engineering industry |
|
| » Posted by: Qingdao Shun Cheong Machinery Co., Ltd [China] |
|
|
|
|
|
[Sell]
Air Cooling Type Batch-off Cooler |
|
|
| Air Cooling Type Batch-off Cooler is used for cooling, folding and depositing the rubber strip that comes from the open mills or twin screw extruder. Structure: There are two kinds: overhead and floor-standing types. Batch off cooler can coat with isolation agent, cooling and laminated storage of the rubber sheet which extruding from mixing and plastic mixing, the structure is floor-standing type. The rubber sheets running have overhead type and multilayer conveying type two kinds. This batch off cooler can be equipped with coding device, lengthcutting or crosscutting, automatic swing glue; automatic laminated rubber sheet weighing and cutting, automatic sampling etc. The new type chain-type batch off cooler uses South Korean technology. The rubber sheet in the chain-belt is using multi-layer reciprocating cooling method. It is suitable for cooling thin rubber sheet and no pollution rubber sheet. |
|
| » Posted by: Qingdao Shun Cheong Machinery Co., Ltd [China] |
|
|
|
|
|
«back
Pages: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 next»
|
|
|
