|
|
|
|
|
|
|
[Sell]
Pad printing silicone rubber |
 |
|
1. Applications of pad printing silicone rubber :
Pad printing silicon rubber is mainly applicable to the printing of irregular patterns on plastics toys, electroplating products, electronic toys, trademarks, artwork gifts, and stationery, etc.
2. Brief description of pad printing silicone rubber:
Pad printing silicone rubber as a carrier which transfer patterns on the steel plate to the toys products surface.
3.Features of pad printing silicone rubber:
a) Resistance to deformation, high-temperature
b) High printing times
c) Good aging resistance
d) Exceptional elasticity
e) Great printing effect
4. Please dont hesitate to ask if you have any questions about mould making silicone rubber, here Chique liu is at your service:
Te*le: 86-755-8994-8019
F*ax: 86-755-8994-8030
Ph*one:86-150-0209-9601
E*m*ail: hyjh(at)szrl(dot)net
|
|
» Posted by: Shenzhen Hong Ye Jie Technology Co.,Ltd. [China]  |
|
|
|
|
|
[Sell]
Addition cure silicone rubber |
|
|
1.Applications of addition cure silicone rubber:
Addition cure silicone rubber is mainly used for metallic arts & crafts, baby nipples, cakes, candy food grade products mold making, life casting, medical catheter and so on.
2. Brief description of addition cure silicone rubber:
Addition cure silicone rubber is mainly used for metallic arts & crafts, baby nipples, cake, candy food grade products mold making, medical catheter and so on. It is nontoxic and with very low shrinkage.
3.Features of addition cure silicone rubber:
a) Two-component silicone rubber with platinum catalyst.
b) With high transparency, tensile strength, and tear strength.
c) Nontoxic & reach to Food grade.
d) With good heat stability and weatherability ( temperatureresistant range of -60—250 C).
e) With heat-ageing resistanc
4. Please dont hesitate to ask if you have any questions about mould making silicone rubber, here Chique liu is at your service:
Te*le: 86-755-8994-8019
F*ax: 86-755-8994-8030
Ph*one:86-150-0209-9601
E*m*ail: hyjh(at)szrl(dot)net |
|
| » Posted by: Shenzhen Hong Ye Jie Technology Co.,Ltd. [China] |
|
|
|
|
|
[Sell]
Electronic potting silicone rubber |
|
|
1.Applications of electronic potting silicone rubber:
HY 9055 electronic potting silicone rubber could be applied to high powered electronics, DC/DC module and circuit board which requires heat dissipation and high temperature resistance.It can also be broadly used for LED screen, Wind Power Generator, PCB substrate, etc.
2. Brief description of electronic potting silicone rubber:
HY 9055 Electronic potting silicone rubber can be applied to electronic components for insulation, waterproofing, fixed and flame retardant. It mainly applied in electronic components surface with materials of PC etc.
3.Features of electronic potting silicone rubber:
a) Moderate viscosity
b) Easy operation
c) Resistant to deformation and inherent flame resistance
d) Nontoxic and Durable
e) The higher temperature the faster of the curing time.
4. Please dont hesitate to ask if you have any questions about mould making silicone rubber, here Chique liu is at your service:
Te*le: 86-755-8994-8019
F*ax: 86-755-8994-8030
Ph*one:86-150-0209-9601
E*m*ail: hyjh(at)szrl(dot)net |
|
| » Posted by: Shenzhen Hong Ye Jie Technology Co.,Ltd. [China] |
|
|
|
|
|
[Sell]
Electronic potting silicone rubber |
|
|
1.Applications of electronic potting silicone rubber:
HY 9055 electronic potting silicone rubber could be applied to high powered electronics, DC/DC module and circuit board which requires heat dissipation and high temperature resistance.It can also be broadly used for LED screen, Wind Power Generator, PCB substrate, etc.
2. Brief description of electronic potting silicone rubber:
HY 9055 Electronic potting silicone rubber can be applied to electronic components for insulation, waterproofing, fixed and flame retardant. It mainly applied in electronic components surface with materials of PC(Poly-carbonate),PP,ABS,PVC, etc.
3.Features of electronic potting silicone rubber:
a) Moderate viscosity
b) Easy operation
c) Resistant to deformation and inherent flame resistance
d) Nontoxic and Durable
e) The higher temperature the faster of the curing time.
4. Any further information about electronic potting silicone rubber, please feel free to contact Mr. Chique:
Te*le: 86-755-8994-8019
F*ax: 86-755-8994-8030
Ph*one:86-150-0209-9601
E*m*ail: hyjh(at)szrl(dot)net
w*ww(dot)sellsilicone(dot)com
|
|
| » Posted by: Shenzhen Hong Ye Jie Technology Co.,Ltd. [China] |
|
|
|
|
|
[Sell]
Addition cure silicone rubber |
|
|
1.Applications of addition cure silicone rubber:
Addition cure silicone rubber is mainly used for metallic arts & crafts, baby nipples, cakes, candy food grade products mold making, life casting, medical catheter and so on.
2. Brief description of addition cure silicone rubber:
Addition cure silicone rubber is mainly used for metallic arts & crafts, baby nipples, cake, candy food grade products mold making, medical catheter and so on. It is nontoxic and with very low shrinkage.
3.Features of addition cure silicone rubber:
a) Two-component silicone rubber with platinum catalyst.
b) With high transparency, tensile strength, and tear strength.
c) Nontoxic & reach to Food grade.
d) With good heat stability and weatherability ( temperatureresistant range of -60---250 C).
e) With heat-ageing resistanc
4. For more information of addition cure silicone rubber, please feel free to contact Mr. Chique:
Te*le: 86-755-8994-8019
F*ax: 86-755-8994-8030
Ph*one:86-150-0209-9601
E*m*ail: hyjh(at)szrl(dot)net
w*ww(dot)sellsilicone(dot)com
|
|
| » Posted by: Shenzhen Hong Ye Jie Technology Co.,Ltd. [China] |
|
|
|
|
|
[Sell]
Pad printing silicone rubber |
|
|
1. Applications of pad printing silicone rubber :
Pad printing silicon rubber is mainly applicable to the printing of irregular patterns on plastics toys, electroplating products, electronic toys, trademarks, artwork gifts, and stationery, etc.
2. Brief description of pad printing silicone rubber:
Pad printing silicone rubber as a carrier which transfer patterns on the steel plate to the toys products surface.
3.Features of pad printing silicone rubber:
a) Resistance to deformation, high-temperature
b) High printing times
c) Good aging resistance
d) Exceptional elasticity
e) Great printing effect
4. Please dont hesitate to ask if you have any questions about pad printing silicone rubber, here Chique liu is at your service:
Te*le: 86-755-8994-8019
F*ax: 86-755-8994-8030
Ph*one:86-150-0209-9601
E*m*ail: hyjh(at)szrl(dot)net
w*ww(dot)sellsilicone(dot)com
|
|
| » Posted by: Shenzhen Hong Ye Jie Technology Co.,Ltd. [China] |
|
|
|
|
|
[Sell]
Manual molding silicone rubber |
|
|
1.Applications of manual molding silicone rubber:
Manual molding silicone rubber is mainly used for model design of manual mold, PVC plastic molds, cement products, low melting point alloy molds, alloy toys, plastic toys, electronics, handicrafts, stationery, large-scale sculpture, reproduction of cultural relic, shoe sole molds, pad printing allocation, Electronic equipment antivibration, etc.
2. Description of manual molding silicone rubber:
manual molding silicone rubber is a flowable liquid, and the quality has nothing to do with the color. It consists of two parts. Part A is a flowable liquid silicone rubber, part B is the curing agent. Dealing with the original model by polish the surface and print release agent first, take some liquid silicone rubber , add 2%-3% curing agent of the amount of silicone, and mix them evenly. Then after vacuum-pumping the mixture, you can pour it into the mold frame. The silicone mold will be cured in 2-3 hours and after 24 hours you can put it into production.
Note: The time for vacuum-pumping should be less than 3-5 mins ,otherwise, once the silicone rubber has cross-link reaction during vacuumizing, and no more further steps will be available.
3.Features of manual molding silicone rubber:
a) Good elasticity
b) Non-deformation
c) Heat resistanct
d) Low shrinkage
4. Please dont hesitate to ask if you have any questions about manual molding silicone rubber, here Chique liu is at your service:
Te*le: 86-755-8994-8019
F*ax: 86-755-8994-8030
Ph*one:86-150-0209-9601
E*m*ail: hyjh(at)szrl(dot)net
w*ww(dot)sellsilicone(dot)com
|
|
| » Posted by: Shenzhen Hong Ye Jie Technology Co.,Ltd. [China] |
|
|
|
|
|
[Sell]
Mold making silicone rubber |
|
|
1.Applications of mold making silicone rubber:
Mould making silicone rubber is suitable for industries such as toys, gifts, furniture decoration, construction decoration, human replica, stationeries, resin crafts, unsaturated resin crafts, poly resin crafts, candle crafts, plastic crafts, plaster crafts, artificial plant and animal crafts ,Buddhist statue crafts.
2. Description of mold making silicone rubber:
Mold making silicone rubber is a flowable liquid, and the quality has nothing to do with the color. It consists of two parts. Part A is a flowable liquid silicone rubber, part B is the curing agent. Dealing with the original model by polish the surface and print release agent first, take some liquid silicone rubber , add 2%-3% curing agent of the amount of silicone, and mix them evenly. Then after vacuum-pumping the mixture, you can pour it into the mold frame. The silicone mold will be cured in 2-3 hours and after 24 hours you can put it into production.
Note: The time for vacuum-pumping should be less than 3-5 mins ,otherwise, once the silicone rubber has cross-link reaction during vacuumizing, and no more further steps will be available.
3.Features of mold making silicone rubber:
a) Good characteristics of easy-operation
b) Good flowability and light viscosity
c) Low shrinkage
d) No deformation
e) Favorable tension
f) Favorable hardness
g) High temperature resistance, acid and alkali-resistance and ageing resistance
4. Please dont hesitate to ask if you have any questions about mold making silicone rubber, here Chique liu is at your service:
Te*le: 86-755-8994-8019
F*ax: 86-755-8994-8030
Ph*one:86-150-0209-9601
E*m*ail: hyjh(at)szrl(dot)net
w*ww(dot)sellsilicone(dot)com
|
|
| » Posted by: Shenzhen Hong Ye Jie Technology Co.,Ltd. [China] |
|
|
|
|
|
[Sell]
RTV silicone rubber similar to Smooth-on |
|
|
RTV silicone rubber similar to Smooth-on
Application of RTV silicone rubber similar to Smooth-on
RTV silicone rubber is mainly be used as following:
1. Decoration building mould making, including architecture column, porch column, interior column etc
2. Unsaturated rein crafts, epoxy resin crafts, poly resin crafts , plastic toys and so on.
3. Concrete decoration, garden statue ,plant, sculpture, Buddha and animal crafts ..
Features of RTV silicone rubber similar to Smooth-on
1 Two part of liquid fluid: liquid white silicone and curing agent.
2 Cure at room-temperature within 4-8 hours, but all performance will act perfectly when it cure within 24 hours.
3 Good fluidity and excellent operation.
4 Good resistance to weather, temperature, aging, acid..
5 Excellent tear strength, comfortable duplication times.
Compare our RTV silicone rubber with Smooth-on silicone rubber
Model MoldMax 25 HY-625
Appearance Purple White
Mixing proportion of curing agent(%) 5% 3-5%
Curing time (hours) 16-18 4-8
Shore Hardness (Shore A) 25 25
Viscosity (Mpas-25℃) 25000 22000
Tear-strength (kfg/cm ) 30 30
Tensile-strength (kgf/cm) 4.2 3.9
Elongation-break (%) 375 450
Retractility (%) ≤0.2 ≤0.3
We have similar silicone to Smooth on but with more competitive price.
For get further information about our silicone product, PLS contact with Miss Cherry
Mobile: 0086-13410795929
TEL: 0086-755-89948294
FAX: 086-755-89948030
Email: cherryyu802 (at) hotmail (dot) com
hyjc(at)szrl(dot)net
Welcome to visit www (dot)szrl (dot)net .anytime .
|
|
| » Posted by: Shenzhen Hong Ye Jie Technology Co., Ltd [China] |
|
|
|
|
|
[Sell]
Pad Printing Silicone Rubber |
|
|
Pad Printing Silicone Rubber Usages:
Pad printing silicone rubber is mainly use for printing irregular patterns of plastic toys, electroplating toys and trade makers. Pad printing silicone rubber as a carrier which transfer patterns on the steel plate to the toys products surface.
.
Pad Printing Silicone Rubber Features:
Pad printing silicone rubber with high print times and abrasion resistance. Pad printing silicone rubber has good printing effects, permanent and durable. We can provide all kinds of color and our catalyst is free.
.
Pad Printing Silicone Rubber Operation Instructions:
Pad printing silicone rubber is two-component silicone, part A is liquid silicon rubber, part B is catalyst. The usual mixture of silicone rubber and catalyst is 100 to 2 or 100 to 3.we take 100g of liquid silicon rubber and 2g-3g catalyst, mix them and pour it to your mold. After 2 to 4 hours, you will get a Pad printing silicone rubber.
.
Frequently asked question of pad printing silicone rubber:
The reasons why the silicone pad has a short service life are listed as follows:
(1)The problem caused by inappropriate filtration of silicone rubber, and impurities in the packaging process due to the uncleanness of barrels and bags.
(2)The short service life of the silicone pad has a close relationship with the adding amount of silicone oil. The more the silicone oil added, the softer the silicone pad will be. The silicone oil will destroy the molecule of the silicone rubber, thereby bringing about the non-durable and easy ageing of the silicone pad.
(3)All the users should know the properties of pad printing silicone rubber. The service life of the silicone pad has close relationship with the size of the printed patterns. For example, if a big pattern to be printed, a big silicone pad is required; if a small pattern to be printed, a small silicone pad (the silicone pad has to be adjusted according to the size of the patterns, and the proportion between the size of the silicone pad and the pattern is 3:1.)
.
For get further information about our silicone product, PLS contact with Miss Cherry
Mobile: 0086-13410795929
TEL: 0086-755-89948294
FAX: 086-755-89948030
Email: cherryyu802 (at) hotmail (dot) com
hyjc(at)szrl(dot)net
Welcome to visit www (dot)szrl (dot)net .anytime .
.
|
|
| » Posted by: Shenzhen Hong Ye Jie Technology Co., Ltd [China] |
|
|
|
|
|
[Sell]
RTV Manual mold silicone rubber |
|
|
RTV Manual mold silicone rubber applications
RTV manual mold silicone rubber is mainly applicable to manual mold design, PVC plastic molds, cement product molds, melting point alloy molds, alloy toy craftworks, plastic toy craftworks, gifts and stationery, large statues, duplication of cultural relics, shoe sole mold fabrication, pad printing positioning, shock resistance for electronic equipments, etc.
RTV Manual mold silicone rubber features description
The RTV manual mold silicon rubber features with the resistance to deformation, good tensile strength as well as low shrinkage, and time of reproduction determined on the basis of customers.
Manual mold silicone rubber operations
Firstly process and prepare the model mold or the product to be duplicated, take certain amount of the silicon rubber, add 2% to 3% solid curing agent, and mix evenly and they are ready for use. One pair of mold can be solidified and formed in 2 to 3 hours.
Frequently asked questions for Manual mold silicone rubber
What should we do when the air bubbles appeared in the process of mold making ?
To handle this situation depends on different cases. Under the condition of an available vacuum pumping machine, mix the silicon rubber and curing agent evenly and then take it to vacuum chamber to deair . If without a vacuum pumping machine, reduce the amount of the curing agent properly. For example, change the mixing ratio of the silicon rubber and the curing agent from former 4% to 1%-2%. In this way, the pre- crosslinking time of silicon rubber will slow down, so the air in the mold will be eliminated gradually to reduce the air bubbles.
For get further information about our silicone product, PLS contact with Miss Cherry
Mobile: 0086-13410795929
TEL: 0086-755-89948294
FAX: 086-755-89948030
Email: cherryyu802 (at) hotmail (dot) com
hyjc(at)szrl(dot)net
Welcome to visit www (dot)szrl (dot)net .anytime .
|
|
| » Posted by: Shenzhen Hong Ye Jie Technology Co., Ltd [China] |
|
|
|
|
|
[Sell]
Liquid Mold making silicone rubber |
|
|
Liquid Mold making silicone rubber applications
Liquid Mold making silicone rubber is primarily intended for poly resin crafts,PU crafts,PU resin crafts ,gypsum crafts ,unsaturated resin crafts, lighting and candles crafts ,plastic toy , stationery gifts crafts industry, a large statue Buddha, relievo furniture, furniture decorative materials, statues Buddha, artifacts copied, building decoration materials, large-scale cement mold, artificial fossils Factory,Europe component factory, simulation landscapes, animals and plants sculpture, sandstone crafts and so on.
Liquid Mold making silicone rubber features
Liquid Mold making silicone rubber is white or red flowing liquid with general hardness of 22-50A°after curing. Molding silicon rubber is a kind elastic silicon rubber mold which features with resistance to deformation, high-temperature, acid-alkali and expansion as well as high reproduction times, good tensile strength ,tear strength and elongation.
Liquid Mold making silicone rubber operations
If the customer wants to make large products and large size molds, the mold should be made of silicon rubber with high hardness. On the contrary, if the mold with fine and precision patterns, it should be made of silicon with low hardness. The amount of the curing agent depends on the actual requirements of the customer. If molds requiring fast drying and demould, more curing agent is needed; contrarily, if molds requiring slower drying and demould, less curing agent is needed.
(Note: our company does not recommend you to add silicone oil. If a special soft silicon mold or fine detailed and complex patterns products are required, 5%-10% silicone oil can be added to soften the mold for easy demould.)
For get further information about our silicone product, PLS contact with Miss Cherry
TEL: 0086-755-89948294
Mobile: 0086-13410795929
FAX: 086-755-89948030
Email: cherryyu802 (at) hotmail (dot) com
hyjc(at)szrl(dot)net
Welcome to visit www (dot)szrl (dot)net .anytime .
|
|
| » Posted by: Shenzhen Hong Ye Jie Technology Co., Ltd [China] |
|
|
|
|
|
[Sell]
Shoe mold Silicone Rubber |
|
|
Shoe mold Silicone Rubber Usages:
HY-218 silicone rubber mainly used for shoe molds, sand casting, sole sampling, plaster models, simple products, products with non-complex patterns, as well as product models with stable size and non-deformation.
Shoe mold Silicone Rubber introduction
Component A is white flowing liquid and component B is the curing agent. For example, take silicone rubber of 100g and add 3-5% curing agent for mixing evenly. After the silicone rubber and the curing agent are completely mixed, put the silicon into a vacuum machine for deairing to remove the bubbles. After deaired, pouring the liquid silicone rubber into the product to be duplicated or into the mold frame.
For get further information about our silicone product, PLS contact with Miss Cherry
TEL: 0086-755-89948294
Mobile: 0086-13410795929
FAX: 086-755-89948030
Email: cherryyu802 (at) hotmail (dot) com
hyjc(at)szrl(dot)net
Welcome to visit www (dot)szrl (dot)net .anytime .
|
|
| » Posted by: Shenzhen Hong Ye Jie Technology Co., Ltd [China] |
|
|
|
|
|
[Sell]
Condensation Electronic Potting Silicone Rubber |
|
|
Features & Applications of Electronic Potting Silicone Rubber
HY 210 is condensation silicone potting compound in two parts with low viscosity.
It can be cured completely at room temperature. HY 210 works on the surface of material as PC(Poly-carbonate),PP,ABS,PVC as to its superior bonding feature. It is also applicable for insulation, waterproof and bonding of electronics parts. It meets the requirements of European RoHS.
Electronic Potting Silicone Rubber Typical Application
- Potting for Protetion of general electronic Module.
- Outdoor protection for LED screen.
Electronic Potting Silicone Rubber TECHNICAL GUIDELINES
1, Please put part A and part B in separate container and stir evenly before mixing the two parts together.
2, Weight Ratio: part A: part B = 10:1
3, Bubble release if necessary. Deaeration the mixture under 0.08 MPa for 3 minutes.
4,HY 210 is cured at room temperature, so pls put it under room temperature after pouring.It comes to next process when basically cured, and it takes about 24 hours for completely cured.
Kindly note: Temperature and Humidity with a tremendous influences for curing of HY 210.
For get further information about our silicone product, PLS contact with Miss Cherry
TEL: 0086-755-89948294
Mobile: 0086-13410795929
FAX: 086-755-89948030
Email: cherryyu802 (at) hotmail (dot) com
hyjc(at)szrl(dot)net
Welcome to visit www (dot)szrl (dot)net .anytime .
|
|
| » Posted by: Shenzhen Hong Ye Jie Technology Co., Ltd [China] |
|
|
|
|
|
[Sell]
liquid rtv silicone rubber for sculpture molding |
|
|
Usage of liquid rtv silicone rubber for sculpture molding
Liquid rtv silicone rubber for sculpture molding is intended for making silicone rubber mold for resin crafts, candles, plastic toys, relieve furniture, architectual decoration, furniture decoration, sculpture and so on.
Feature of liquid rtv silicone rubber for sculpture molding
Liquid rtv silicone rubber for sculpture molding is flowing liquid with general hardness of 22-50 A ° after curing with features:
1)low shrinkage
2)good operation
3)high tear and tensile strength
4)curing agent free
5)easy de-mold
6)high reproduction times
7)resistance to deformation and high-temperature, acid-alkali
Operations of liquid rtv silicone rubber for sculpture molding
If customers want to make large products and large size moulds, the mould should be made of silicone rubber with high hardness. On the contrary, if the mould with fine and precision patterns, it should be made of silicone with low hardness. The amount of the curing agent depends on the actual requirements of the customer. If mould requiring fast drying and demould, more curing is needed.
For get further information about our silicone product, PLS contact with Miss Cherry
TEL: 0086-755-89948294
Mobile: 0086-13410795929
FAX: 086-755-89948030
Email: cherryyu802 (at) hotmail (dot) com
hyjc(at)szrl(dot)net
Welcome to visit www (dot)szrl (dot)net .anytime .
|
|
| » Posted by: Shenzhen Hong Ye Jie Technology Co., Ltd [China] |
|
|
|
|
|
[Sell]
silicon for pad printing |
|
|
silicon for pad printing application:
silicon for pad printing is mainly applicable to the printing of irregular patterns in big-size or intricate design on plastic toys, electroplating products, electronic toys, trademarks, artwork gifts, stationery, etc.
silicon for pad printing features:
Model 918
Viscosity(cps) 20000
Hardness(Ao) 26
Tensile Strength (Kgf/cm2) 38
Tear Strength (kgf/cm) 19
Elongation(%) 380
Mixing ratio (%) 2-3
Pot Life(H) 0.5
Curing Time(H) 2-4
silicon for pad printing FAQs:
Why the silicon pad is non-durable？
1. It has something to do with the addition of silicone oil. More silicone oil added, softer the pad printing will be, meanwhile the pad will be turned to be non-durable and easy ageing;
2. Some customers are unawre of the performance of silicone rubber. Actually, the durability of silicone printing pad is closely related to the size of printing patterns. Usually, we use large silicon pad for big patterns. On the contrary, small silicone pad ofr small patterns. Generally, the ratio of pad to pattern is 3:1.
Why the silicon pad did not absorb the ink?
Any silicon pad or liquid silicon rubber could absorb ink well. If large patterns or big letters need to print, the printing pad will for sure absorb ink well. For small letters, please do not use hard silicon pad, as it could not absorb the printing ink thoroughly from the steel plate.
Any questions of Pad Printing Silicone Rubber, please feel free to contact Cassi.
Shenzhen Hong Ye Jie Technology Co.,LTD
TEL: 086-755-89948006
FAX: 086-755-89948030
MOBILE:086-15220073603
Website: www(dot)szrl(dot)net
E-MAIL: hyjg（at)szrl(dot)net |
|
| » Posted by: Hong Ye Jie Technology Limited Company [China] |
|
|
|
|
|
[Sell]
Pad Printing Silicone Rubber |
|
|
Brief description:
Pad printing silicone :
1. resistance to deformation, high-temperature
2. high printing times
3. good aging resistance
4. exceptional elasticity
5 great printing effect
Pad Printing Silicone Rubber Usages:
Pad printing silicone rubber is mainly use for printing irregular patterns of plastic toys, electroplating toys and trade makers . Pad printing silicone rubber as a carrier which transfer patterns on the steel plate to the toys products surface.
.
Pad Printing Silicone Rubber Features:
Pad printing silicone rubber with high print times and abrasion resistance. Pad printing silicone rubber has good printing effects, permanent and durable. We can provide all kinds of color and our catalyst is free.
.
Models of pad printing silicone rubber,
NO.: HY-918
Usage: The best quality in pad printing silicone for making pads.
description: HY-918# with the advantages of abrasion resistance, high temperature resistance, good printing effect, etc.The silicon pad is a carrier which transfer printing the patterns on the steel plate onto the toy products' surface.
FAQ:Why the silicon pad can not transfer the printing pattern well?
It is normal phenomena that every two out of ten products have this problem if the plastic toys are not spray painted. As in the production process, mold release agent will be sprayed onto the surface of the steel plate for each one dozen products, and there will be some mold release agent left on the surface of the first one or two product. Please use Tianna water or face-clean water to clean the products before used for pad printing.
Any questions of Pad Printing Silicone Rubber, please feel free to contact Cassi.
Shenzhen Hong Ye Jie Technology Co.,LTD
TEL: 086-755-89948006
FAX: 086-755-89948030
MOBILE:086-15220073603
Website: www(dot)szrl(dot)net
E-MAIL: hyjg（at)szrl(dot)net |
|
| » Posted by: Hong Ye Jie Technology Limited Company [China] |
|
|
|
|
|
[Sell]
Condensation Silicon Rubber |
|
|
Condensation Silicon Rubber Application:
Condensation Silicon rubber is mainly used for the duplication and mold making of poly resin crafts, PU crafts, gypsum or plaster, unsaturated resin, lighting and candles crafts, plastic toy, stationery gifts crafts, large statue buddha, furniture decoration, cement, articficial stone, etc.
Condensation Silicon Rubber Features:
Model 630
Viscosity(cps) 24000
Hardness(Ao) 28
Tensile Strength (Kgf/cm2) 40
Tear Strength (kgf/cm) 23
Elongation(%) 400
Mixing ratio (%) 2-3
Pot Life(H) 0.5-1
Curing Time(H) 2-5
Condensation Silicon Rubber FAQ:
Why does the condensation silicon rubber mold appear to be dry outside but wet inside?
Usually, we will dry out the water of the condensation silicon rubber to make sure its long shelf-life, while condensation silicon rubber is a kind of condensation silicon rubber, which get solidified after absorbing water from the air.
The best solution to it is to add 0.05% water into the silicon rubber and stir it slowly when you want to use it.
Any questions of silicone rubber for mold making, please feel free to contact Cassi :
TEL: 086-755-89948006
FAX: 086-755-89948030
MOBILE:086-15220073603
Website: www(dot)szrl(dot)net
E-MAIL: hyjg(at)szrl(dot)net |
|
| » Posted by: Hong Ye Jie Technology Limited Company [China] |
|
|
|
|
|
[Sell]
Mold Making Silicone Rubber |
|
|
Mold Making Silicone Rubber Application:
Mold making silicone rubber is particulary suitable for small-sized products in pouring way, which mainly used for the duplication and mold making of poly resin crafts, PU crafts, gypsum or plaster, unsaturated resin, lighting and candles crafts, plastic toy, stationery gifts crafts, large statue buddha, furniture decoration, cement, articficial stone, etc.
Mold Making Silicone Rubber Features:
Easy-operation;
Light viscosity and good flowability;
Low shrinkage;
Favorable tension;
No deformation;
Favorable hardness;
High temperature resistance, acid and alkali-resistance and ageing resistance.
Mold Making Silicone Rubber FAQ
Why silicone rubber mold just can be reproduced for a few times?
Three factors can lead to such a problem:
1. Adding too much silicone oil into the mold making silicone rubber, for silicone oil is an additive which destroies the molecular weight of mold making silicone rubber and reduce the tesion and tear strength;
2. Using the mold making silicone rubber with a low hardness to make molds for small-size products in delicate and intricate designs, or the mold making silicone rubber with a low hardness to make molds for large-size products in simple designs;
3. Putting the mold making silicone rubber molds into mass reproduction within 24 hours. In most cases, we advise our customers mass reproduction with silicone rubber molds in 24 hours, because the performance of mold making silicone rubber can be stable in 24 hours.
Any questions of Mold Making Silicone Rubber, please feel free to contact Cassi :
TEL: 086-755-89948006
FAX: 086-755-89948030
MOBILE:086-15220073603
Website: www(dot)szrl(dot)net
E-MAIL: hyjg(at)szrl(dot)net |
|
| » Posted by: Hong Ye Jie Technology Limited Company [China] |
|
|
|
|
|
[Sell]
RTV-2 Mold Making Silicone Rubber |
|
|
RTV-2 Mold Making Silicone Rubber Application:
RTV-2 mold making silicone rubber is mainly applied for making various molds, such as reproduction of poly resin, epoxy, polyurethane-polymer, plaster, gypsum, soaps, candle& lighting, architecture, decorative arts and crafts, plastic toy, gift and stationery, big statue, cultural relic products, and etc.
RTV-2 mold making silicone rubber advantages: good tension and tear strength, high reproduction times and with restistance of high temperature, etc.
RTV-2 Mold Making Silicone Rubber Features:
Easy-operation;
Light viscosity and good flowability;
Low shrinkage;
Favorable tension;
No deformation;
Favorable hardness;
High temperature resistance, acid and alkali-resistance and ageing resistance.
RTV-2 Mold Making Silicone Rubber Opearations:
RTV-2 mold making silicone rubber contains two parts: part A is liquid silicone rubber, part B is curing agent.
1. Mix both A and B parts totally by weight at the ratio of 100:2 (A to B) in a clean container. Making sure that A and B mixed evenly, otherwise the compound will be partly solidified and this will give birth to difficulties in the following operations, leading to the short life of your final molds.
2. Degas the compound by a vacuum pump about 3-5 minutes (usually no more than 10 minutes), otherwise, it will cause cross linking reaction, and no more further operations will be available.
3. Make molds in brushing way or pouring way according to the size of your products.
Any questions of silicone rubber for mold making, please feel free to contact Cassi :
TEL: 086-755-89948006
FAX: 086-755-89948030
MOBILE:086-15220073603
Website: www(dot)szrl(dot)net
E-MAIL: hyjg(at)szrl(dot)net |
|
| » Posted by: Hong Ye Jie Technology Limited Company [China] |
|
|
|
|
|
«back
Pages: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 next»
|
|
|
