|
[Sell] CVG-200 Canners Vacuum Gauge |
|
|
the Canneed "CVG-100 and CVG-200 Canner's Vacuum Gauge", Used to measure the vacuum pressure of seamed cans. The gauge is placed on top of the can and the piercing needle is forced through the top of the can. The rubber collar forms a temporary seal to allow for measurement. CVG-100 is designed for using near the product line, Consists of a 0 to 76cm Hg vacuum gauge, pierce point, and rubber collar. Also available with dual scale to measure pressure to 15 psi. CVG-200 is designed for using in lab, Consists of a holder, a 0 to 76cm Hg vacuum gauge, pierce point, and rubber collar. Also available with dual scale to measure pressure to 15 psi. Technical data (Changes reserved): Vacuum range : 0-0.1 Mpa; (0-15 Psi; 0-76 cmHg) Resolution: 0.005 Mpa Accuracy: +/-2.5%
|
|
» Food & Beverages/Equipment |
|
|
|
[Sell] CAN-7001 CO2 Tester and Pressure Tester |
|
|
The “CAN-7001 CO2 tester and Pressure Tester “is used to measure the CO2 content in carbonated beverages filled in glass and PET bottles and cans. Once the bottle or can is placed in the tester, the handle is pulled forward and the sample is pierced consecutively. The pressure is read on the pressure gauge, as soon as the equilibrium pressure is achieved. With a dial thermometer install with model CAN-7001-T, the temperature of the liquid is read at the same time. With model CAN-7001, the bottle or can may then be removed from the instrument to measure the temperature of the liquid with a separate thermometer. The CO2 content is determined by means of the CO2 slide rule or temperature/pressure relationship charts. Technical data (Changes reserved): Press: Measuring range : 0-0.6Mpa Resolution : 0.01 Mpa. Temperature: Measuring range : 0-50℃ Resolution : 0.1℃ Sample capacity : Height: min. 50mm, max. 330mm Bottle diameter: Max. 90mm Dimensions : 200 x 130 x 400 mm (W x D x H) Net Weight : 2 kg For air determinations the IAM Air Meter can be combined with CAN-7001 or CAN-7001-T. • Determination of air content in the headspace volume, • Determination of total air content in the beverage.
|
|
» Food & Beverages/Equipment |
|
|
|
[Sell] SST-2 Secure Seal Tester For Bottle And Lid |
|
|
The “Canneed SST-2 Secure Seal Tester “is used to test seal integrity on the glass or plastic containers and cans. The SST-2 has been designed to address the special needs of sealing cans and bottles that use aluminum roll-on, twist crowns, or plastic caps. The SST-2 operates with compressed air, nitrogen, or carbon dioxide. By detecting gas leakage, rather than liquid, the Secure Seal Tester gives more sensitive, accurate readings. SST-2 is constructed from anodized aluminum, stainless steel, and plastic materials. The tester's rugged construction withstands production line abuse, yet is accurate enough for laboratory use. Technical data: Measurement range : 0-16 bar (1.6 Mpa) Pneumatic supply : Max. 16 bar (1.6 Mpa) Sample capacity : 330 mm height × 150 mm dia. max. Dimensions : 320 x 380 x 720 mm (W x D x H) Net Weight : 15 kg
|
|
» Food & Beverages/Equipment |
|
|
|
[Sell] IDG-100 Can Internal Diameter Gauge |
|
|
IDG-100, IDG-200 & IDG-300 Can Internal Diameter Gauge This unit serves for quickly checking the Internal Diameter of can. It is supply with a calibration piece. IDG-100 is for small diameter cans, Cans dia. 52-100 mm (only measure one type can), If equipped with the data processor, it can be auto calculate to achieve the actual internal diameter of the 2-piece cans, and avoid the measurement deviation caused by the "ellipse effect". IDG-200 is for large diameter cans, Cans dia. :80-260 mm (only measure one type can) IDG-300 is compatible for two (2) or three (3) sizes of cans. One type cans must equip with one calibration pieces and one set of measure blocks (change parts). If you must measure several type cans, you can order several pcs of IDG-100 or IDG-200. Or you can order several psc of calibration pieces and several sets of measure blocks. Technical data: Resolution : 0.01 mm
|
|
» Food & Beverages/Equipment |
|
|
|
[Sell] AXL-4000 Axial Load Tester |
|
|
The “CanNeed AXL-4000 Axial Load Tester” measures the axial force resistance of beverage cans in Newton. The can is placed in a support and gradually forced upwards against the pressure plate. The space between the support and the top plate can be altered with spacers. The can crashes after the peak force has been applied that the can is capable of resisting. The maximum value can now be read in the display 1)Industry Standard 2)Exceptionally Parallel Platens 3)Auto record and display the peak force value 4)Touch-screen PLC Controlled 5)Stable pressing process, data collected automatically by the microcomputer controlling system 6)Pressure plate auto reset after the test is finished. Convenience for placing / taking out the samples. 7)Display the max. and min. measuring value and average after several test. 8)Applicable for samples of different dimension. 9)Mechanical Overload Protection Configuration: AXL-4000 Axial Load Tester already included the 330ml fitting insert. Optional: 500ml fitting insert. AXL-CAL Calibration Cell For Axial Load Tester. Technical data: Measure range : 3000 N Resolution : 1N Rear Panel : RS232 Power supply : 240VAC 50-60Hz Dimensions : 500 mm x 400 mm x 600 mm (W x D x H ) Weight : 50 kg
|
|
» Food & Beverages/Equipment |
|
|
|
[Sell] CBT-100 Buckle Tester Bottom for Can |
|
|
The "Canneed CBT-100 Buckle Tester Bottom for Cans" determines the exact pressure at which the can bottom begins to buckle respectively the dome reverses. The empty flanged can or straight wall can is placed in the holder. After covering the device with a plexiglass hood pressure is applied. The can is sealed with a rubber o-ring structure. Fast pressure increase up to 5 bar (programmable to just bellow the expected buckle value), from there the „speed of pressure increase“ may be set within the device. The test is terminated as soon as the can buckles. The maximum pressure value is shown in the display. Any can of varying diameter and height may be tested: inserts are available that can be exchanged within seconds. Feature: *Industry Standard * suit empty flanged can and straight wall can *Program Logic Control System (PLC) Controlled *LCD touch-screen Display *Rs-232 Communications Capability * Overload Protection *Test Point For Calibration *"speed of pressure increase"may be set *display the max. and min. measuring value and average after several test. Technical data (changes reserved): Measure range: 0-900 Kpa Resolution: 1 Kpa Rear Panel: RS232 serial output Power supply: 115/230V/50...60Hz Pneumatic supply: 10bar Dimensions: 600 x 450 x 430 (W x D x H ) Weight: 40 kg
|
|
» Food & Beverages/Equipment |
|
|
|
[Sell] ELT-100 Leak Tester for ends |
|
|
The Canneed Leak Tester for End ELT-100 is designed for 2 ends. The end is sealed in the compound area and Pressure is applied. Leaking spots are made visible by revealing bubbles in the water bath. Each end diameter or shape requires specially adjusted holders, which can be exchanged easily. Technical data: (changes reserved) Pressured air supply: 6 bar min. Max. test pressure: Ø 50 mm: 6 bar, Ø 83 mm: 3 bar, Ø 99 mm: 2 bar Dimensions: 400 x 600 x 220 mm Weight: approx. 32 kg Water overflow bath size: 10 L
|
|
» Food & Beverages/Equipment |
|
|
|
[Sell] ACH-100 Aerosol Curl Height Gauge |
|
|
The Canneed ACH-100 Aerosol Curl Height Gauge is used for measuring the contact height of the curl 1" aperture of aerosol cans. ACH-100 is the Industry Standard. The gauge is first calibrated by setting the calibration ring on the gauge. In this case the dial has to indicate the value of 4.25 mm. The measurement on the can is then inserting the gauge up to the shank into the can and then slowly releasing the button. Technical data: Measure range: 0-10mm Resolution: 0.01mm
|
|
» Food & Beverages/Equipment |
|
|
|
[Sell] CLT-600 Leak Tester for can |
|
|
The canneed"CLT-600 Leak Tester for can" is used for checking the permeability of 3-piece cans in a water bath. The can is fixed to magnet disc plate and submerged into the water. At the same time it is subjected to pressure and leaks are revealed by air bubbles. End and side seams visible. A special parallel clamping system enables to measure different diameters and heights with one device. The clamping pressure and the test pressure may be set independantly. The operator determines the period of time the cans are under water. If he switches the by-pass lever and presses the two button valves, the cans deaerate and are lifted out of the water. The whole test cycle is automated and is pneumatically controlled by pressure regulator valves. Technical data (changes reserved): Maximum test pressure: 4 bar Max. diameter: 130 mm Max. can height: 300 mm Bath dimensions: 1500 x 600 x 500 mm (W x D x H) Dimensions: 1500 x 800 x 800 mm(W x D x H) Weight: 200 kg
|
|
» Food & Beverages/Equipment |
|
|
|
[Sell] DER-4 Digital Enamel Rater |
|
|
DER-4 Digital Enamel Rater The CanNeed DER-4 Digital Enamel Rater is able to detect the exposed metal position more easily compare to the former models. The reformative electronic design makes it more sensitive, reliable and accurate. The anticorrosion characteristic of the enhanced can body support is ensured its durability. The film coated buttons are more durable and with better corrosion resistance. DER-4 is the industry standard. The new CanNeed Enamel Rater DER-4 instrument test the coverage of the enamel coating inside food and beverage cans, aerosol-cans and also different kinds of ends. It displays an index of the amount of metal exposed by incomplete enamel coverage on a clear, easily read digital LED. The instrument applies a constant voltage across the can body and an electrode immersed in an electrolyte-filled can, and measures the resulting current. Test voltage is set at 6.3 VDC. Operating range is 0 to 500 milliamperes with accurate resolution within 0.1ma. The instrument operates in industry standard 4 second mode, continuously, or can be programmed to measure any desired time. In 4-second mode, the display shows the reading only at 4 seconds. In continuous mode the reading is displayed beside elapsed time with the 4-second reading automatically stored in memory for recall. A simple and foolproof calibration self-test verifies correct, accurate operation. Location of exposed metal can be determined by reversing voltage which causes bubbles of gas to form on exposed metal for easy visual identification. Electrolyte level and can contact sensors ensure that testing begins only when can is properly filled with electrolyte solution and good electrical contact with the can has been established. The sturdy enclosure includes a sealed-membrane keypad for protection against moisture and corrosion in the factory environment. An RS232 serial interface permits use with remote computers, printers or data collectors. The CanNeed End Panel Holder can be used with any CanNeed Enamel Rater to test for metal exposure on can ends. The test is performed in the same manner as on a can. Electrolyte is added to the plastic cup, the can end is fitted onto the beveled end of the cup, and a vacuum is applied to hold the end securely on the cup. When the cup is inverted, the electrode and can end become immersed in the electrolyte and the reading is displayed on the Enamel Rater. The CanNeed End Panel Holder consists of a lucite cup mounted to rotate on its horizontal axis. The cup is beveled to make a tight seal on the can end. An electrode and vacuum connection are mounted within the cup. On the bakelite base a vacuum stopcock and a moveable contact arm, which completes the electrical circuit when the assembly is inverted. A cable adaptor footswitch is required to connect a CANNEED End Panel Holder to the CANNEED Digital Enamel Rater. Technical Specifications (changes reserved): Sample type : 2- and 3-piece cans, aerosol-cans and different kinds of ends Range : 0 to 500 ma Resolution : 0.1mA Accuracy : ± 5% Power supply : AC115 V/230V to DC9V Rear Panel : RS232 serial output Display unit Dimensions : 162 x 200 x 80mm ( W x L x H ) Can holder Dimensions : 210 x 228 x 250 mm (W x L x H) Weight : 4 kg
|
|
» Food & Beverages/Equipment |
|
|
|
[Sell] CSS-100B Anti-noise seam saw |
|
|
CSS-100B Anti-noise seam saw The saw is provided with an anti-noise design and a special guide for 2- and 3-piece cans (65 mm dia.). Special seam circular saw with double cut for can double seam inspections. The CSS 100B was specially designed for 2- and 3-piece cans. The nitrated blades achieve together with the speed of approx. 1.000 r/min. a very plain cut surface. The seam image on VSM 6A Automatic Seam Computer (Video Seam Monitors), and automatic seam measuring systems gets thereby very clear and improves measurement speed and reliability. Technical data (changes reserved): Sample can dia. : 65mm Sample type : 2- and 3-piece cans. Saw blades: 80 x 22 x 0,5 mm , Speed: approx. 1.000 r/min. Power supply: 230 V; also available with 115 V motor Dimensions: L380×W240×H200mm Weight : 12kg
|
|
» Food & Beverages/Equipment |
|
|
|
[Sell] Seam Sight(TM) Full Automatic Seam Monitor |
|
|
The Seam SightTM Full Automatic Seam Monitor is a compact measuring system for quick and accurate automatic seam measurements and storing of seam images. The seam is positioned manually in front of the camera and is digitised by the computer. In less than 1 second the Seam SightTM software offers a measurement. The seam length, body hook, end hook, actual overlap, percentage overlap; seam gap, seam thickness and body hook butting% are measured. At the end of the measurement an evaluated seam appears including dimension lines and measured values. This may be stored in computer or printed out on a laserprinter. The values can be stored in a Excel file and are displayed in on-screen if values are within specs. Feature: 1. In less than 1 second the Seam SightTM software offers a measurement. 2. With the Golden LensTM get very clear Seam image 3. Data can be stored in a Excel file! 4. Measured values are displayed in on-screen and alarm if values are not within specs! 5. Seam image can be printed, stored! 6. Calibration function 7. LED Illumination 8. SPC function to collect the data of Mitutoyo micrometer. Seam SightTM Full Automatic Seam Monitor consisting of: * Seam Monitor * Seam SightTM Software * Calibration piece 2mm Optional: *Digital Seam Thickness Guage *Digital Countersink Guage *Interface to Seam SightTM Seam SightTM Full Automatic Seam Measuring System If the Seam SightTM Full Automatic Seam Monitor combine with the Digital Seam Thickness Guage, Digital Countersink Guage and Interface, it is a Seam SightTM Full Automatic Seam Measuring System. Technical data (changes reserved): Power supply: 115 / 230V Accuracy: +/- 0.005 mm Languages: English / Chinese Cans dia. :52-200 mm, custom made up to 300mm Dimensions: 400 X 200 X 150 mm(W X D X H) Weight: 5 kg
|
|
» Food & Beverages/Equipment |
|
|
|
|
|
Pages: 1
|
|
|