|
|
|
Offer
From Non Premium Member |
|
|
|
Type: |
Sell |
| Subject: |
molding silicone rubber HY620 |
| Description: |
Molding Silicone Rubber HY620 Description:
Molding Silicone Rubber HY620 is mainly used for toy gifts and craftwork gifts with the advantages of good tensile strength, high tear strength, high temperature resistance, high duplication times and repeated use, etc. It is suitable for small products or fine and precision products which is difficult to demould. This molding Silicone Rubber is one of the products with the highest use level in the production of craftwork gifts and the shrinkage is up to 2‰.
Molding Silicone Rubber Standard Datasheet:
Model 620
Appearance White
Viscosity (cps) ≤16000
Hardness (A°) 20±2
Tensile strength (Mpa) ≥2.8
Tear strength (KN/m) ≥20
Elongation (%) ≥400
Mixing ratio (%) 2~3
Operating time(H) 0.5~1
Curing time(H) 2~5
Molding silicone rubber Operation Instruction:
Molding silicone rubber is white or red flowing liquid with general hardness of 18-22A°after curing . If the customer wants to make large products and large size molds, the mold should be made of silica gel with high hardness. On the contrary, if the mold with fine and precision patterns , it should be made of liquid silicone with low hardness. The amount of the curing agent depends on the actual requirements of the customer. If molds requiring fast drying and demould, more curing agent is needed; contrarily, if molds requiring slower drying and demould, less curing agent is needed.
(Note: our company does not recommend you to add silicone oil. If a special soft liquid silicone mold or fine detailed and complex patterns products are required, 5%-10% silica gel oil can be added to soften the mold for easy demould.)
Molding Silicone Rubber FAQ:
Why is the appearance of the finished mold striate and unsmooth?
It is because the appearance of the product or the model itself is not perfect, and it has not been polished before the further operation. So when you make silicon molds, firstly you should polish the products, spray the realese agent evenly on the product. In this case, the problem can be avoided.
Any further information pls feel free to contact with Ms Nina
TEL: 0086-755-89948019
Fax: 0086-755-89948030
E-mail: hyjr(at)szrl(dot)net
Website: www(dot)szrl(dot)net
|
| Placement Date: |
Jun 21, 2012 |
| Expiration Date: |
Jun 20, 2017 |
|
|
|
|
|
|
Company Name: |
Shenzhen Hong Ye Jie Tech Co., Ltd. |
| Contact Person: |
Ms Nina |
| City: |
Shenzhen |
| Country: |
China
 |
| Local Time: |
|
| E-mail: |
Premium
Membership Required (Join Free Today) |
|
| Introduction: |
Hong Ye Jie Technology Co., Ltd. was established in 1998, it is a Science and technology corporation which is engaged in production, R & D, and sales of silicone rubber. We sets up Hong Kong Hongye Ltd., Shenzhen Hongye silicone rubber Factory and other affiliated enterprises in 2005.
Our products including silicone products like silicone rubber, RTV-2 molding silicone rubber, manual design silicone rubber, shoe sole mold silicone rubber, silicon oil, pad printing silicone rubber, encapsulant and potting compound, silicone rubber for LED display, electronic thermolysis ointment, thermal conductivity silicone, special silicone rubber for CPU, silicone tube, silicone membrane, silicone sealant , liquid silicone rubber, addition cure RTV silicone rubber, HTV silicone rubber, solid silicone rubber, gross rubber, silicone rubber sheet, hot stamping silicone plates & roller, etc. These are currently been exported to Southeast Asia, Europe, the America and other 50 countries and regions. |
| Business Type: |
Exporter, Manufacturer |
| Areas of Interest: |
1. Chemicals/Rubber
|
|
